Barbecook SIESTA 310 BLACK EDITION Mode D'emploi page 29

appliance may
differ from the examples in the figures.
6. Proceed as follows:
• If you detect a leak, follow the instructions in
"7.6 In the event of a gas leak".
• If there are no leaks, close the gas supply, rinse all parts
thoroughly with water, and dry them well.
7.6. In the event of a gas leak
1. Close the gas supply and proceed as follows:
• If you have detected a leak on one of the connections,
firmly tighten the connection in question.
• If you have detected a leak on the gas bottle or hose,
replace the gas bottle or hose.
2. Check the connection or part where you detected the leak
again.
3. If the leak has not been fixed, you must contact a
Barbecook dealer. You must not start using the appliance
until the leak has been fixed.
Consult www.barbecook.com for a list of
Barbecook dealers near you.
8. PREPARING THE APPLIANCE FOR USE
8.1. Before each use
Whenever you use the appliance, you must ensure that:
• The appliance is set up in a suitable location
See "3.3 Choosing a suitable location".
• The hose does not drag over the ground and cannot come
into contact with hot surfaces or dripping fat.
• The bowl is clean. We recommend cleaning the
bowl after every use. See "11.2 Cleaning the bowl".
• The burners and venturi tubes are not blocked by insect
nests or spider webs. See "11.3 Cleaning the burners and
venturi tubes".
• The burners are correctly fitted.
The venturi tubes must be situated above the openings
of the gas valves.
To be absolutely certain that the gas connections are in
order, you can check the appliance for gas leaks before
each use.
See "7. Checking for gas leaks".
8.2. Before first use (or after a lengthy period
out of use)
If you are using the appliance for the first time or after a
lengthy period
out of use, you must carry out some additional checks:
• Ensure that you have read all of the instructions in this
guide, understood them, and checked them (before first use
only).
• Check the appliance for gas leaks.
See "7. Checking for gas leaks".
Check that there are no gas leaks if the appliance has
been assembled by the supplier.
• Clean the burners and venturi tubes (only after a lengthy
period out of use).
See "11.3 Cleaning the burners and venturi tubes".
• Allow the appliance to "burn in" before placing any food
on the grill (only before first use). See "8.3 Burning in the
appliance".
29
8.3. Burning in the appliance
Burning in the appliance before first use helps to remove any
manufacturing greases that may still be present.
Proceed as follows:
1. Ignite the main burners and set the control knobs to HIGH.
See "9.2 Igniting the main burners".
2. Close the lid and allow the appliance to burn for 15 minutes.
Do not put any food on the grill yet.
3. After 15 minutes, open the lid and let the appliance burn for
a further 5 minutes (control knobs still set to HIGH).
4. After these 5 minutes, the appliance is ready for use and
you can place food on the grill.
9. IGNITING THE BURNERS
To ignite the burners with the electric igniter, you must
insert an AA battery into the igniter. The battery is not
supplied with the appliance. The battery compartment
for the igniter is located on the control panel for the
appliance.
9.1. Safety instructions
• Before igniting the appliance, carry out all checks as
specified in "8. Preparing the appliance for
use".
• Ensure that the lid is open whenever you ignite
a burner.
• Never bend directly over a burner when igniting
it.
9.2. Igniting the main burners
9.2.1 Using the igniter
1. Open the lid and set the control knobs for the main burners
to OFF.
2. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
3. Press the control knob for a burner, set it to HIGH, and
leave it in place. The in-built igniter will create sparks, which
will ignite the burner.
burner first. Never
same time.
4. If the burner does not ignite after three attempts, set the
control knob for the burner to OFF, close the gas supply,
and wait for 5 minutes to allow the accumulated gas to
escape.
5. Attempt to ignite the burner again. If it still does not ignite,
attempt to ignite the burner with a match or consult "14.
Rectifying problems" in order
to identify the cause of the problem.
9.2.2 Using a match
1. Place a match in the match holder.
2. Open the lid and set the control knobs for the main burners
to OFF.
3. If no other burner has yet been ignited,
open the gas supply and wait for ten seconds
for the gas to stabilize.
4. Strike the match and hold it around 13 mm
away from the burner.
www.barbecook.com
Start by igniting one main
ignite all main burners at the