Publicité
NOTICE! Possible damage to property in the event of abrupt disconnection
from the power supply.
2.7.2.
Securing the system against being switched on again
1. Shut down the goods issuing system, disconnect it from the power supply and
check that it is electrically dead.
2. Secure the hazard area around the goods issuing system, place clear warning
signs in position around the working area, and issue a prohibition against it be-
ing switched on again.
3. On completion of the work, reinstate the fuses and guards.
4. Check the guards and safety devices for correct operation, and remove the warn-
ing notice.
3.
Device overview
3.1.
TOOL24 LOCKER
A
1 Touch-screen monitor (master
system)
2 Emergency release lock
3 Computer unit
4 Body
5 Control unit
3.2.
NAMEPLATE
Designation:
Commercial Designation:
Series / Type / Item number:
Voltage / Phases / Frequency:
Full load current / SCCR:
Power:
10
Serial Number / YOC:
9
Ho mann Supply Chain GmbH
Poststraße 15 • 90471 Nuremberg • Germany
1 General designation
2 Trade name
3 Series / type / article number
4 Voltage in V / phases / frequency
in Hz
5 Full load current in A / max. short-
circuit current in kA
3.3.
CONNECTION OVERVIEW
Main system (MASTER)
H
No. Connection type
1
IEC C14 connector
2
IEC C13 connector
3
USB output
4
RJ45 port
Expansion module
I
No. Connection type
1
IEC C14 connector
2
IEC C13 connector
3
USB output
4
USB input
i
The industrial vending system has an additional cable outlet on the rear with rub-
ber grommet in order to protect the cable from damage.
6 Pallet truck base with LED lighting
7 Emergency release fascia with LED
strip
8 Goods issuing flaps
9 Barcode scanner (1D standard, 2D
accessory)
For UK: Ho mann UK Quality Tools Ltd,
Holborn Hill, Birmingham, B7 5JR
6 CE and UKCA marking
7 Electrical and electronic device
identification
8 Manufacturer's address
9 Serial number / build year
10 Rated power in kW
Function
Power supply (output) expansion modules
power supply (input)
Power supply (input)
Connection of expansion modules
Connection with network
Function
Power supply (output) expansion modules
power supply (input)
Power supply (input)
Connection of expansion modules
Connection of expansion module with
main system (MASTER)
i
The Lockers can be connected sequentially/in series until the following Windows
message appears. If this message appears, the last Locker connected was one too many
and must be connected to the master via a separate USB port.
i
Windows message: You have exceeded the number of supported USB devices.
You have exceeded the number of supported USB devices on the Intel USB 3.0 eX-
tensible host controller. Disconnect an unused USB device or connect one of the
devices to a different port.
4.
Transport, place of erection and storage
i
Immediately on receipt check the product for damage in transport. If the product is
damaged, do not install or commission it.
WARNING
Suspended loads
Risk of fatal accidents, together with crush hazards, laceration hazards and impact
hazards for the body and limbs.
»
Transport work must be performed by trained persons who have been instructed
in the safety aspects of hoists and transport work.
»
Use only tested means of transport, lifting gear and slings that are suitable for the
weight and size of the item to be transported.
»
Do not enter under suspended loads or reach under them or into their range of
swinging.
»
Be aware of the position of the centre of gravity of the device.
»
Do not run lifting gear such as ropes and straps across sharp edges and corners.
Do not knot them, do not twist them.
»
Check that the attachment of the lifting gear is secure.
»
Move loads only under proper supervision. Before you leave the workplace, first
1
set down the load.
2
CAUTION
3
Risk of injury during transport
4
Risk of injury from improper transport to installation site.
5
»
Wear foot protection, safety gloves and safety helmet.
»
Do not transport alone.
6
»
Make sure the paths for movement and transport are clear.
7
»
If features, release parking brake on castors and apply before work.
8
»
Transport with drawers and doors closed, locked and additionally secured.
NOTICE
Improper transport
Damage to items of packaging.
»
Handle items of packaging in accordance with the symbols and instructions
shown on them.
»
Do not drag them across the floor.
»
When items of packaging are being transported they must be upright, secured
with ropes and protected against slipping.
»
Be aware of the centre of gravity.
»
Use the lifting points provided.
»
When putting them down, do so slowly and evenly.
»
Do not remove the transport packaging until immediately before erection.
»
Once the device has been erected at the place of erection, remove the transport
restraints.
4.1.
LIST OF SYMBOLS
Symbol
Meaning
Keep items of packaging dry and protect them from moisture.
Items of packaging with fragile or delicate contents. Handle them
with care, do not drop them, do not subject them to impacts.
Arrows facing upwards indicate the top of the item of packaging
and must always point upwards in order that the contents do not
suffer damage.
Do not stack packages.
4.2.
TRANSPORT DIMENSIONS
Article no. 979300 Size 450/10
Length
1000 mm
Width
1200 mm
Height
2150 mm
Gross weight
210 kg
Article no. 979310 Size 450/10
Length
1200 mm
Width
1000 mm
Height
2200 mm
Gross weight
210 kg
Size 300/14
Size 180/40
1050 mm
1000 mm
1050 mm
1200 mm
2200 mm
2150 mm
200 kg
275 kg
Size 300/14
Size 180/40
1000 mm
1000 mm
1200 mm
1200 mm
2150 mm
2150 mm
200 kg
275 kg
www.hoffmann-group.com
de
en
bg
da
fi
fr
it
hr
lt
nl
no
pl
pt
ro
sv
sk
sl
es
cs
hu
15
Publicité
