Publicité
Switching the Laser Level On
and Off . . . . . . . . . . . . . . . . . . . . 29
Positioning the Laser Level . . . . . . . . 29
Horizontal Alignment with the
Laser Line . . . . . . . . . . . . . . . . . . 29
Vertical Alignment with the Laser
Line . . . . . . . . . . . . . . . . . . . . . . 29
Alignment Off of Reference
Points . . . . . . . . . . . . . . . . . . . . . 30
Maintenance and Lubrication . . . . . . . . . 31
Service . . . . . . . . . . . . . . . . . . . . . . . 31
Batteries. . . . . . . . . . . . . . . . . . . . . . 31
General Power Tool Safety Warnings
below may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Clut-
tered or dark areas invite accidents.
b. Do not operate power tools in explo-
sive atmospheres, such as in the pres-
ence of flammable liquids, gases or
dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away
while operating a power tool. Distrac-
tions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces, such as pipes, ra-
diators, ranges and refrigerators. There
1600A034F4 AA Dremel DD12V OSI 20240729.indd 3
1600A034F4 AA Dremel DD12V OSI 20240729.indd 3
Table of Contents
Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed
SAVE THESE INSTRUCTIONS
Tool Lubrication . . . . . . . . . . . . . . . . 31
Motors . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning. . . . . . . . . . . . . . . . . . . . . . 31
Stud Finder . . . . . . . . . . . . . . . . . . . 31
Accessory Storage and
Maintenance . . . . . . . . . . . . . . . . 31
Attachments and Accessories . . . . . . 31
Troubleshooting . . . . . . . . . . . . . . . . . . . 32
Dremel® Limited Warranty . . . . . . . . . . . 34
is an increased risk of electric shock if
your body is earthed or grounded.
c. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp
location is unavoidable, use a Ground
Fault Circuit Interrupter (GFCI) pro-
tected supply. Use of a GFCI reduces
the risk of electric shock.
3
7/29/2024 5:00:16 PM
7/29/2024 5:00:16 PM
Publicité
