Parkside 311700 Traduction Du Mode D'emploi D'origine page 27

Noise and vibration information:
Noise measurement value determined in accordance with ISO 22868,
EN 10517. The A-rated noise level of the power tool is typically as follows:
Hedge trimmer:
Sound pressure level L :
pA
Uncertainty K :
WA
Sound power level L :
WA
Guaranteed sound power level L
Uncertainty K :
WA
Pole pruner:
Sound pressure level L :
pA
Uncertainty K :
WA
Sound power level:
Uncertainty K :
WA
3-section cutting blade:
Sound pressure level L :
pA
Uncertainty K :
PA
Sound power level L :
WA
Uncertainty K :
WA
Strimmer:
Sound pressure level L :
pA
Uncertainty K :
PA
Sound power level L :
WA
Uncertainty K :
WA
Wear ear protectors to prevent hearing damage!
Vibration values (vector total of three directions) determined in ac-
cordance with EN 11806-1, EN ISO 10517, EN ISO 11680-1:
Hedge trimmer:
Vibration on the front handle: vibration emission value
a
Uncertainty K = 1.5 m/s
Vibration on the rear handle: vibration emission value
a
Uncertainty K = 1.5 m/s
Pole pruner:
Vibration on the front handle: vibration emission value
a
Uncertainty K = 1.5 m/s
Vibration on the rear handle: vibration emission value
a
Uncertainty K = 1.5 m/s
Strimmer:
Vibration on the front handle: vibration emission value
a
Uncertainty K = 1.5 m/s
Vibration on the rear handle: vibration emission value
a
Uncertainty K = 1.5 m/s
3-section cutting blade:
Vibration on the front handle: vibration emission value
a
Uncertainty K = 1.5 m/s
Vibration on the rear handle: vibration emission value
a
Uncertainty K = 1.5 m/s
│
■ 22 GB│IE
98.79 dB(A)
2.5 dB
109.53 dB(A)
: 114 dB(A)
WA
2.5 dB
97.06 dB(A)
2.5 dB
110.87 dB(A)
2.5 dB
97.64 dB(A)
2.5 dB
111.27 dB(A)
2.5 dB
99.08 dB(A)
2.5 dB
111.10 dB(A)
2.5 dB
= 4.182 m/s 2
h,D
2
= 9.695 m/s 2
h,D
2
= 3.855 m/s 2
h,D
2
= 7.590 m/s 2
h,D
2
= 4.864 m/s 2
h,D
2
= 9.750 m/s 2
h,D
2
= 4.622 m/s 2
h,D
2
= 7.708 m/s 2
h,D
2
NOTE
► The vibration level specified in these instructions has been measured
in accordance with the standardised measuring procedure specified
in EN ISO 11806-1, EN ISO 10517, EN ISO 11680-1 and can be
used to make equipment comparisons. The specified vibration emis-
sion value can also be used to make an initial exposure estimate.
WARNING!
► The vibration level varies in accordance with use and may be higher
than the value specified in these instructions in some cases. There is a
risk of underestimation of the vibration load if the appliance is used
regularly in this manner. To estimate the vibration load during a spe-
cific working period accurately, periods during which the appliance
is switched off (or running, but not being used) must also be taken
into account. This can significantly reduce the vibration load over the
total working period.
WARNING!
■ You can reduce the vibration risk, for example, the risk of Raynaud's
phenomenon, by taking regular breaks during which you rub your
hands together.
Explanation of the symbols used
Warning! Read the operating instructions before use!
Wear protective gloves!
Wear safety shoes!
Wear ear protection!
Wear a hard hat!
Wear protective goggles!
Important, hot parts. Keep a safe distance away!
1
1. Switch on the appliance
I
ON
o
2
2. Fill fuel pump (primer)
FULL
3
3. Pull the choke lever
PULL
4
4. Pull the starter pull cord
PULL
CHO KE
Pull the choke lever
PBK 4 A1