Reflex Servitec 35 Mode D'emploi Original page 46

Controller
10 Controller
10.1 Configuring settings in the controller
You can configure the controller settings regardless of the currently selected and
active operating mode.
10.1.1 Customer menu
10.1.1.1 Customer menu – overview
Use the Customer menu to correct or determine system-specific values. In the
course of initial commissioning, the factory settings must be adjusted for the
system-specific conditions.

Note!
For a description of the operation,  8.1 "Operator panel",  41.
A three-digit PM code is assigned to the setting options
PM Description
code
001 Select the language
002 Set the time
003 Set the date
004 Select the system type
•
Levelcontrol
•
Magcontrol
minimum operating pressure,  7.2 "Setting the
005 Set the P
0
minimum operating pressure for Magcontrol",  41.
006 Set the actuating pressure for the system safety valve.
–
The actuating pressure protects the device.
Degassing ˃
•
012 Degassing programme
•
Continuous degassing
•
Interval degassing
•
Run-on degassing
•
013 Continuous degassing time
Make-up >
• Maximum make-up time ...min.
023
• Maximum make-up cycles ... /2 h.
024
•
Frequency of make-up cycles in 2 hours.
•
024 Make-up pressure
–
Standard = Make-up pressure ˃ 2.3 bar.
– Setting range 1.3 – 2.3 bar.
–
< 1.3 bar.
•
027 With contact water meter "Yes/'No".
–
If "Yes", continue with 028.
–
If "No", continue with 007.
•
028 Reset make-up quantity "Yes/No".
–
If "Yes", reset to "0".
•
029 Maximum make-up quantity ... l
•
030 Water treatment "Softening / Desalination / None".
–
If "Softening", continue with 031.
–
If "Desalination", continue with the next point
–
If "None", continue with 007.
With conductivity monitoring "Yes/'No".
•
031 Shut off make-up "Yes/No" (if water capacity is exhausted).
•
032 Soft water capacity ... l
–
Calculation required before input.
•
Fillsoft I + softening:
Soft water capacity = 6000 l / hardness reduction.
•
Fillsoft I + desalination:
Soft water capacity = 3000 l / hardness reduction.
•
Fillsoft II + softening:
Soft water capacity = 12000 l / hardness reduction.
•
Fillsoft II desalination:
Soft water capacity = 6000 l / hardness reduction.
46 — English
PM
code
033
034
007
008
10.1.1.2 Setting the customer menu - "Time" example
The setting of system-specific values is explained below using the setting of the
time as example.
To adjust the system-specific values, proceed as follows:
1.
2.
3.
Vacuum spray degassing — 01.04.2022-Rev. D
Description
• Hardness reduction ... °dH = GHactual – GHtarget
–
Can be called when softening or desalination is active.
–
Calculate the required reduction in overall hardness
GH before input.
• replacement interval... months (for softening cartridges
according to manufacturer).
Maintenance interval... months
Floating contact
•
Message selection >
• Message selection: only messages marked with "√"
are output.
•
All messages: All messages are output.
Fault memory > History of all messages
Parameter memory > History of parameter input
Display settings > Brightness, screen saver
Information >
•
Position of the "PV" 2-way motorized ball valve at the
pressure side of the pump.
–
Position in %
•
Software version
Press "Settings".
–
The controller switches to the setting area.
Press "Customer >".
–
The controller opens the Customer menu.
Press the required area.
–
The controller switches to the selected area.
–
Use the scroll bar to navigate through the list.