Table des Matières
Publicité
Implémentation MIDI
❍ Data set 1
DT1
Status
Data byte
F0H
41H, dev, 00H, 6BH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte
Explanation
F0H
Exclusive status
41H
ID number (Roland)
dev
Device ID (dev: 00H - 1FH, 7FH)
00H
Model ID #1 (Fantom-X6/X7/X8)
6BH
Model ID #2 (Fantom-X6/X7/X8)
12H
Command ID (DT1)
aaH
Address MSB: upper byte of the starting address of the data to be
sent
bbH
Address:
upper middle byte of the starting address of the data
to be sent
ccH
Address:
lower middle byte of the starting address of the data
to be sent
ddH
Address LSB:
lower byte of the starting address of the data to be
sent.
eeH
Data:
the actual data to be sent. Multiple bytes of data are
transmitted in order starting from the address.
:
:
ffH
Data
sum
Checksum
F7H
EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in Parameter Address Map (P.311).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to P.329.
* Not received when the Receive Exclusive parameter (SYSTEM/MIDI) is OFF.
Status
Data byte
F0H
41H, dev, 42H, 12H, aaH, bbH, ccH,
ddH, ... eeH, sum
Byte
Explanation
F0H
Exclusive status
41H
ID number (Roland)
dev
Device ID (dev: 10H - 1FH, 7FH)
42H
Model ID (GS)
12H
Command ID (DT1)
aaH
Address MSB: upper byte of the starting address of the transmitted
data
bbH
Address:
middle byte of the starting address of the transmitted
data
ccH
Address LSB:
lower byte of the starting address of the transmitted
data
ddH
Data:
the actual data to be transmitted. Multiple bytes of
data are transmitted starting from the address.
:
:
eeH
Data
sum
Checksum
F7H
EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in Parameter Address Map (P.311).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to P.329.
* Not received when the Receive Exclusive parameter (SYSTEM/MIDI) is OFF.
304
2. Data Transmission
Status
F7H
■ Channel Voice Messages
● Note off
Status
8nH
n = MIDI channel number:
kk = note number:
vv = note off velocity:
● Note on
Status
9nH
n = MIDI channel number:
kk = note number:
vv = note on velocity:
● Polyphonic Key Pressure
Status
AnH
n = MIDI channel number:
kk = note number:
vv = Polyphonic Key Pressure:
● Control Change
* By selecting a controller number that corresponds to the setting of parameters of
❍Bank Select (Controller number 0, 32)
Status
BnH
Status
BnH
F7H
n = MIDI channel number:
mm, ll = Bank number:
* These messages are transmitted when Patch, Rhythm Set or Performance is selected. But
* In Performance mode, these messages are not transmitted when External Bank Select
* Although with the Fantom-X you can select the Bank Select messages to be transmitted,
* The Bank Select Numbers corresponding to SRX series should be referred to the SRX
❍Modulation (Controller number 1)
Status
BnH
n = MIDI channel number:
vv = Modulation depth:
❍Breath type (Controller number 2)
Status
BnH
n = MIDI channel number:
vv = Control value:
❍Portamento Time (Controller number 5)
Status
BnH
n = MIDI channel number:
vv = Portamento Time:
❍Data Entry (Controller number 6, 38)
Status
BnH
BnH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
2nd byte
kkH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
00H - 7FH (0 - 127)
2nd byte
kkH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
01H - 7FH (1 - 127)
2nd byte
kkH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
00H - 7FH (0 - 127)
controllers (REALTIME CONTROL knob, and so on), the Fantom-X can transmit any
control change message.
2nd byte
00H
20H
0H - FH (ch.1 - 16)
00 00H - 7F 7FH (bank.1 - bank.16384)
not transmitted when Transmit Program Change or Transmit Bank Select parameter
(SYSTEM/MIDI) is OFF.
MSB or External PC Number parameter (PERFORMANCE/PART) is OFF.
be sure to refer to the Program Change Map on P.330 for the Bank Select messages
transmitted when the Fantom-X is select a Patch, Rhythm Set or Performance.
series owner's manual.
2nd byte
01H
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
2nd byte
02H
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
2nd byte
05H
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
2nd byte
06H
26H
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Publicité
Table des Matières
