Emerson AVENTICS XV03 Notice D'instruction page 14

1 About this documentation
Read this documentation completely, especially
ing with the product.
These instructions contain important information on the safe and appropriate as-
sembly, operation, and maintenance of the product and how to remedy simple
malfunctions yourself.
1.1 Documentation validity
This documentation applies to the following series XV product variants:
• XV03
• XV05
This documentation is intended for:
System owners, system planning engineers, machine manufacturers, installers
1.2 Additional documentation
Observe the following related documents:
• Manufacturer's system documentation
• Documentation of other system components
Product
XV03 / 05 valve system and components
Serial / parallel control de- XVES Profinet
pending on configuration
XVES Modbus
XVES Ethernet-IP
XVES EtherCat
XVES Profibus
XVES Multipole
XVES IO-Link
QR code
Link
www.emerson.com/
xv03c
www.emerson.com/
xv05c
1.3 Designations used
This documentation uses the following designations:
Designation Meaning
Separator Disc for creating pressure zones by inserting into cross channels
1.4 Abbreviations used
This documentation uses the following abbreviations:
Abbreviation Meaning
BSPP British Standard Parallel Pipe
ESD Electrostatic Discharge
HNBR Hydrogenated Nitrile Butadiene Rubber
NBR Nitrile Butadiene Rubber (acrylonitrile butadiene rubber)
NPT National Taper Pipe
PELV Protective Extra Low Voltage
PPE Personal protective equipment
PUR Polyurethane
SELV Safety Extra Low Voltage
2 Safety
2.1 About this chapter
• Read this chapter and this documentation completely before working with
the product.
AVENTICS™ XV03 / XV05 | 570365-BAL-AA | English
chapter g 2. Safety
Document Document type
number
570565 Safety information
570088 Operating instructions
570092 Operating instructions
570090 Operating instructions
570089 Operating instructions
570093 Operating instructions
571246 Operating instructions
570096 Operating instructions
Description
Downloads and further information on this product
can be found on the product page at the Emerson
Store.
• Keep this documentation in a location where it is accessible to all users at all
times.
before work-
2.2 Intended use
Applications
• Control of pneumatic actuators
• The product is intended for solely for professional use.
• The product is exclusively intended to be installed in an end product (a sys-
tem/machine) or to be assembled with other components to form an end
product.
Application area and location
• Industrial applications
• Indoor areas
2.3 Improper use
The product is not intended for use in explosive areas (explosion protection).
2.4 Obligations of the operator
• The owner must ensure that persons who assemble, operate, disassemble, or
maintain products must not consume any alcohol, drugs, or pharmaceuticals
that may affect their ability to respond.
• The owner must ensure that PPE is used. Observe all specifications for the
overall system.
2.5 Personnel qualifications
Only personnel qualified for the tasks at hand are allowed to perform the activi-
ties described in this documentation. Depending on the activity, this requires ba-
sic knowledge in the following areas and knowledge of the relevant technical
concepts:
• Pneumatics
• Electrics
2.6 Hazards
2.6.1 Material damage
Damage due to too high mechanical loads
• Never twist or bend the product and add-on parts, or mount them when they
are under tension.
• Do not use the product as a handle or step.
• Do not position any objects on the product.
Damage caused by electrostatic discharge
Contact between people or objects and electrical product components can cause
electrostatic discharge (ESD), which then damages or destroys the product. Take
the following measures to prevent ESD:
• Observe handling instructions and recommendations as per EN 61340-5-1
and EN 61340-5-2.
• Use wrist and shoe grounding when working on the product.
• Never connect or disconnect the plug while it is live.
3 Scope of delivery
• 1x Valve system (see: order)
If you have configured your product with optional elements, these elements
are already assembled on the product.
• 1x grounding screw
• For mounting with DIN rail: 1x adapter kit: 2x DIN clip with 2x screw each
14