Publicité
Les langues disponibles
Les langues disponibles
How to Select a Desired Tune Using CPS
Ex: See (1). To select the 3rd tune past the current tape position, select "3".
(1)
Current tape position
(2)
al
:
]
bP
~
E
Direction of
el
eS
=
tape travel
L
!
=p
a
In example (1), if "t" is less than
head | Before
4 seconds, it will not be counted
|
as
a
blank
space.
Designate
"2"
instead
of
"3"
to
select
the 3rd tune in this case.
(3)
Current tape position
(4)
£]
Direction of
tape travel
Before
CPS Tape Side Decided by REVERSE MODE Switch
Reverse
CPS Tape Side
Mode
Search\
Direction
—.
ED)
CZED
Direction\
Indicator
Cc
Side A only
Side A> Side B
Side
A > Side B > Side A
>>
<j
Side
Bonly | Side B-Side A | Side B + Side A > Side B
ce
Side A only
Side A only
Side
A — Side B — Side A
<j
Side B only
Side B only
Side B > Side A > Side B
~
second side, blank scan is con-
In the middle of a tape
tinuous; otherwise it automatical-
Fast-forward
Play
ly stops after completing a full
loop of tape after the initial side.
{|
Note:
(g
2
elf a tape portion at a particularly low level
is continued
for more than 10 seconds,
|
such as a pianissimo section in classical
music, etc., it may be detected as a blank
and the Blank Scan operation may not
Blank play
for 10 seconds
work correctly.
At the end of either side
y
SIDE 8
Play
Dubbing (Copying
from deck |
to deck II)
[ NORMAL DUBBING
|
To Dub Entire Recorded Section of a
Pre-recorded Cassette
Tape end
Fast-forward
Blank play
for 10 seconds
is reached.
3.Check that both cassettes are fully re-
=>: Stops when the end of the reverse
wound on their left reels before loading
side is reached.
them.
4. Load the pre-recorded cassette into deck
<>): As long
at there is a recorded
9
| and the recordable cassette into deck II.
section before the end of the
2G
5. Set the REVERSE MODE switch to the
=> position.
* If other positions are selected:
==: Dubbing will be performed for
one side only.
C2: Playback of deck | will continue
(repeatedly) and be recorded on
deck II until the tape in deck II
reaches the end of the reverse side.
6.Press the PAUSE button of deck | and/
or Il and press
<
or
»
button to
change
the tape running direction,
if
required. Then
set both
decks to the
stop mode.
7.\f required,
press the BLANK
SCAN
button (its indicator lights) to engage
the blank scan function for deck | during
dubbing.
8.When monitoring, select the settings of
the
NR
SYSTEM
switch.
(The
NR
system switch has no effect on dubbing.)
9.The REC LEVEL control settings will be
ignored during dubbing as they have no
effect.
10.Press DUB START NORM or HIGH to
start dubbing.
The
indicator
of the
button pressed will light.
NORM: Dubbing is performed at normal
speed.
HIGH: Dubbing
is performed
at twice
normal speed.
11. To stop dubbing, press the STOP button
on deck II.
Note:
elf there is a TV set near the W-995RX
during high speed dubbing, it is possible
that the TV's horizontal
scanning fre-
quency (15.75 kHz) will be recorded on
the tape. If this malfunction is detected
and to prevent
it in advance,
dub at
normal
speed,
switch
of the TV
set's
Publicité
