Teac W-995RX Manuel Du Propriétaire page 6

© I/Ml Indicators:
Show the tape counter mode (deck | or II).
@ INTRO CHECK Indicator:
Lights when the INTRO CHECK mode is
activated.
@ DUBBING Indicators:
HIGH: Lights in high-speed dubbing mode.
NORM: Lights in normal-speed dubbing
mode.
@® NR SYSTEM Indicators:
Lights to show the NR system currently
selected.
Operations
Playback with Deck | or II
Set the TIMER switch to OFF.
Press the POWER switch to ON.
Set the REVERSE MODE switch to the
desired tape travel direction.
4. Load a pre-recorded cassette.
5. Select the NR system with the NR
SYSTEM switch.
. Press the < or > button.
. Adjust the volume with the amplifier's
control.
1. Load pre-recorded cassettes in decks |
and Il.
2. Set the necessary switches, except the
< or > button, referring to "Playback
with Deck | or II'.
3. Set the REVERSE MODE switch to the
C>position.
4. Press the < or > button of deck | to
start continuous playback.
5. When the playback of deck | finishes,
deck II playback begins in the forward
direction automatically.
6. After playback of the reverse side of the
tape in deck II finishes, playback starts
in deck | in its forward direction.
7. The above operations will be repeated
continuously 5 times from deck | to II
and vice versa.
8. To clear the continuous play mode, press
the STOP button.
Note:
Continuous playback can be started from
either deck | or Il. In any cases, the
second deck will start playback in the
forward direction.
at ee
OD
To Select a Desired Tune While
a Deck is Playing
While one deck is in the playback mode
(whether it is in the continuous or single
playback mode), you can select the next
tune to be played from a tape loaded in the
other deck, in the following way:
1. Eject the tape in deck | and replace with
the required tape.
2. Using the CPS, CDS or PGM function
(refer to pages 7 — 9 for details), search
for the desired tune, and set the deck
to the play-pause mode at the beginning
of the selected tune.
3. Press the PAUSE button of deck | to
release the play-pause mode. Playback
of deck | starts and deck I! automatical-
ly stops.
Note:
ln this case, while the searching operation
is engaged for deck | (or deck II), Blank
Scan does not function on the other deck.
Recording from a stereo system:
1. Set the TIMER switch to OUT.
. Load a recordable cassette.
. Select the NR system with the NR
SYSTEM switch as required.
Notes:
eWhen recording on only one side of the
tape, set the REVERSE MODE switch to
== (single way) position.
eThe RECORD buttons on deck | and II
can be activated independently. Therefore,
recording can be done on two tapes
simultaneously, in parallel. In this case set
the REVERSE MODE switch to—— (single
way) or —— (reverse) position.
ap
Continuous Recording (Deck | to
Deck 11) ;
1. Load two recordable cassettes on both
decks | and II.
2. Set the NR SYSTEM, etc. as required.
3. Set the REVERSE MODE switch to the
C>position.
4. Press the RECORD button of deck | to
start recording.
5. After recording with deck | is completed,
deck I! starts recording automatically in
the forward direction.
6. To clear the continuous recording mode,
press the STOP button.
Notes:
eln continuous recording, since recording
with deck II always begins in the forward
direction, make sure the cassette loaded in
deck I! can be recorded on both sides.
=6=
eContinuous recording from deck I! to
deck | is impossible.
elf the tape running direction is set to re-
verse side of deck I, recording will be done
on only the reverse side of the tape loaded
in deck |.
Recording order
Deck | Deck II
Side A — Side B + Side A — Side B
Side B +> Side A > Side B
Record Muting Operation — :
For various search features such as PGM,
CDS, CPS, and INTRO CHECK to function
properly, a blank space of about 4 seconds
(or more) is required between tunes.
1. Automatic Spacing Operation — for
a 4-second blank — (during recording)
Press the REC MUTE button during re-
cording. The tape movement continues,
and a blank space of about 4 seconds
is recorded (the RECORD indicator
blinks).
The deck then switches automatically
to the record-pause mode (both the
RECORD and PAUSE indicators light).
To begin recording the next tune, press
the PAUSE button (the PAUSE indi-
cator goes off).
2. Automatic Spacing Operation — for a
4-second blank — (during record-pause)
During the record-pause mode, pressing
the REC MUTE button causes the RE-
CORD indicator to blink to show the
record-muting stand-by mode. As soon
as the PAUSE button is pressed, the tape
runs and the above-mentioned automatic
spacing operation will be initiated.
3. Fora Blank of More Than 4 Seconds
During recording, keep the REC MUTE
button pressed for a longer blank period.
Release the button to enter the record-
Pause mode. To begin recording, press
the PAUSE button.
4. Fora Blank of Less Than 4 Seconds
After pressing the REC MUTE button
during recording, press the PAUSE
button. Or press the REC MUTE button
again to resume recording without
stopping the tape.
INTRO CHECK Facility
This facility makes searching for a specific
tune much easier by continuously detect-
ing the beginning of each tune.
1. Press the INTRO CHECK button.
2. The deck will fast-wind to the beginning
of a tune, play the first 15 seconds (ap-
prox.), and fast-wind to the beginning of
the next tune, from which point the
cycle starts again.
3. To cancel the intro check function, press
the STOP button.