GRE 83037503 Manuel De Montage page 333

WINTER-SEASON:
A) If you choose not to dismount the pool:
1- Clean the liner bottom and sides with a non-abrasive product.
2- Treat the water with a chemical product for wintering. We recommend
using LIQUID WINTERISER instead of floats with solid product to avoid dis-
colouring the liner.
3- Leave the pool full of water considering:
a) For pools with skimmer and refulling pipe, reduce the water level 5 cm
underneath the skimmer and close the refulling pipe with the screw tap
which is included with the filter.
b) For pools with exhaustion and refulling pipes, reduce the water level 20
cm from the superior edge of the pool and close the pipes using the screw
system incorporated.
4- Disconnect the pipes. Do not dismount the skimmer and the refulling
and exhaustion pipes.
5- Protect the pool with a winter cover, and put a floating element between
the cover and the water, in order to protect it from frost.
6- Filter: disconnect it from the pool. Clean it, empty the sand or remove the
cartridge, dry it and keep it in a covered and sheltered from dampness place.
7- Accessories: remove every accessories (ladder, alarm, spotlight, pole...),
rinse them with soft water and tidy them away.
TO RUN THE POOL AGAIN: Remove the winter cover, install the f ilter,
change at least 1/3 of water and realize a chlorine treatment. Switch on the
filter for at least 8 hours in an uninterrupted way, respecting the continuous
working period indicated in the filter manuals.
B) If you choose to dismount the pool:
1- Empty the pool. Measures: Filter, Automatic pump for handling clean wa-
ter or communicating vessels system. Communicating vessels system: Use
the hose from your filter with the smallest cross-section. Fix a weight to one
of its end and plunge it into the swimming pool. After this, sink the whole
hose, until there is no air inside. With one hand, and under the water stop up
hermetically the end of the hose and take it to the emptying point. Remove
hand, and water will start running. Do not use this water for watering the
plants, because it contains chemical products.
2- Clean every pool constituents with a sponge and a soap product with a
neutral pH. Dry them and tidy them away in a dry and clean place.
That's normal that after having installed and dismounted the pool several
times, the P.V.C liner dilate and loose its elasticity.
TO RUN THE POOL AGAIN: Read another time this manual instructions
from the beginning.
PROBLEM
Muddy water
Green water
Brown water
Incustrations
Eyes and skin
irritations. Bad smell.
EMPTYING - COMMUNICATING
VESSELS SYSTEM
CAUSE
Bad filtration. High PH. Organic residues
in
excess
Seaweed or mud formation
Presence of iron or manganese
Presence of Calcareous in the water
Misadjusted PH. Organic residues in
excess
CHEMICAL MEASURES:
Please read carefully the chemical product manufacturer instructions.
WARNING: Keep chemical products in a clean, dry and out of children place.
Important:
Every products used have to be compatible with the P.V.C liner.
→ First filling: Analyse the water pH and chlorine (Cl) and adjust them to
the optimal levels: pH: 7,2 – 7,6; Chlorine: 0.5 – 2 ppm.
→ Chlorine treatments: Consist in increasing the chlorine level until ap-
proximatively 20 ppm to eliminate germs and seaweeds. This process has
to be done only when the pool water comes from rivers or ponds, ... or if it
stayed a long time without any treatments.
→ Checking: Check at least once a week the chlorine levels (use a chlorine
and pH analyser). In the same way, we advise to add an algicid to prevent
seaweeds appearance.
Never have a swim before the chlorine level stabilization. Do always use
a floating dispenser for the chemical product (tablets) dissolution. The
chemical product measuring out has to be done in accordance with: Your
pool water volume, the bathe frequency, the climatic conditions, the water
temperature and the location. Do always move the water and wait for the
chemical product dissolution before adding another one. Wait approxima-
tively 12 hours between any pH, chlorine or algicid adjustment using the
filter system.
MECHANICAL MEASURES:
Check the filter, the skimmer, the valves and the pipes are well connected
to the pool. Do consider high water temperature will involved more time
for the filtering.
Theoretic filtering time = Water volume / Filter system discharge (gener-
ally 8h/day with water temperature of 21°C), (Ideal: 2h in the morning – 4h
around midday – 2h in the afternoon). PLEASE RESPECT THE CONTINUOUS
WORKING PERIOD INDICATED IN THE FILTER MANUALS.
VACUUM CLEANER (MANUAL OR AUTOMATIC):
Only for pools with skimmer. Connect an hose extremity to the brush head
and immerse it into the water to make it fill in. Connect the other pipe
extremity to the exhaustion adapter (TA) and place it above the skimmer
basket. Switch on the filter in the FILTER position and begin to clean the
bottom. Pay special attention to areas with folds where dirt accumulates.
BOTTOM CLEANER VENTURY STYLE:
Connect a garden hose to the bottom cleaner join and introduce it into the
pool. Open the tap until a normal pressure to make the water flow out against
the bottom of the pool, producing in that way an ascendant stream which
leave the dirt into the filter (bag) which is adjust on the bottom cleaner.
SOLUTION
Perform a return was of the filter.
Add PURIFIER in tablets using a dispenser.
Perform a shock chlorinating.
Gently clean the bottom and walls of the pool.
Analyse the pH and adjust it to between 7.2 - 7.6.
Add algicide and liquid purifier.
Analyse the pH and adjust it to between 7.2 - 7.6.
Perform a shock chlorinating. Add liquid purifier.
Analyse the pH and adjust it to between 7.2 - 7.6.
Add anti-calcareous once a week.
Analyse the pH and adjust it to between 7.2 - 7.6.
Perform a shock chlorinating.
E N
maintenance and use
2 5