Publicité
Les langues disponibles
Les langues disponibles
"DW" is displayed. This function allows you to watch two channels..
A new short press SCAN/DW key (7) after short press F key (14)
the DW function. "DW" disappears from the display.
SKIP
(long press only if the SCAN function is activated)
This function allows you to
skip
When the scan stops on an unwanted channel, press and hold the SCAN/
DW key (7) for 1 second to
store
A beep sounds. The channel will no longer be scanned. See the § SCAN
above.
Consult the SCAN SKIP menu page 13 and the RESET menu page 17.
M3
.
See § MEMORY page 8
8) ANL/NB ~ HI-CUT ~ M4
ANL/NB
(short press)
Short press the ANL/NB key (8) to
The activated filter is shown on the display.
ANL - Automatic Noise Limiter: This filter allows the reduction of background
noises and some reception interferences. In AM mode only.
NB - Noise Blanker: This filter allows the reduction of back ground noise,
and some reception interference.
HI-CUT
(long press)
Long press the HI-CUT key (8) to
CUT" appears on the display when the filter is active.
Hi-Cut: Eliminates high frequency interferences. Has to be used in accord-
ance with the reception conditions.
M4
.
See § MEMORY page 8
9) EMERGENCY CHANNELS ~ RF GAIN ~ MIC GAIN
EMERGENCY CHANNELS
Emergency channels will be automatically
(9). First press : emergency channel 1 is activated. Second press: emergency
deactivates
a channel found by the SCAN function.
this channel in the SCAN SKIP memory.
activate/deactivate
the filters in this order:
activate/deactivate
the HI-CUT filter. "HI-
(short press)
selected
by pressing the EMG key
channel 2 is activated. Third press:
appears on the display when an emergency channel is activated.
See § EMERGENCY CHANNEL page 15
RF GAIN
(long press)
Setting the reception sensitivity. Maximum position in the case of long-
distance call reception. You can decrease the RF GAIN, to avoid distortions,
when the interlocutor is near. Reduce the gain on reception in the case
of a close communication with a correspondent not equipped with a RF
POWER.
Long press the RF GAIN/MIC GAIN key (9). "RF GAIN" is displayed.
-
-
Turn the rotary CH knob (54) to
The normal position of this function is at maximum level. The bargraph of
the RF GAIN will always be displayed in reception.
MIC GAIN
(combination 18 + 9)
Adjust the microphone sensitivity level.
-
Press and hold the PTT switch (18)
Press the RF GAIN/MIC GAIN key (9). "MIC GAIN" is displayed.
-
-
Turn the rotary CH knob (4) to
The normal position of this function is at maximum level. MIC GAIN bargrah
will be displayed on transmission.
10) MONITOR ~ CALL
MONITOR
(short press)
This function allows you to monitor the channel despite the squelch.
When ASC is active or the manual squelch level is high, press MONITOR (10)
to hear the active channel.
CALL
(combination 18 + 10)
Press and hold the PTT switch (18).
Press the CALL key (10) to send a preset call melody. «TX» is displayed.
(see § CALL TONE FREQUENCY, page 16).
11) VOX ~ NOISE GATE ~ VOX SETTING
VOX
(short press)
The VOX function allows
transmitting
phone (or in the optional vox microphone) without pressing the PTT switch
(18). The use of an optional vox microphone connected to the rear panel
9
return
to the current channel. "EMG"
.
adjust
the level 01 to 10 or using the bargraph.
adjust
the level 01 to 10 or using the bargraph.
by speaking into the original micro-
Publicité
