Publicité
Les langues disponibles
Les langues disponibles
channel in your local area (see WEATHER FREQUENCY TABLE page 71).
The display shows the selected weather channel and if the unit receives a
signal, "WX" and "A" icons blink.
ALERT
(long press)
The SIREN tone only sounds in
Long press the ALERT key (15), in order to
function. When the function is activated, "Alert" is displayed. If a tone is
detected at the selected weather channel, then the unit sounds SIREN
CB
tone. The unit cancel
mode and go to
During a SIREN tone sound, press PTT key (18) to stop the sound.
16) CLARIFIER
The function CLARIFIER (16) allows a frequency deviation during LSB/USB
reception in order to improve the clearness of your correspondent's voice.
17) USB CHARGING SOCKET
The USB socket (17) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
18) PTT (Push To Talk)
Transmission key, press to
transmit
to
listen to
an incoming communication,
TOT (Time Out Timer)
If the transmission using PTT switch (18) or VOX function is longer than 3
minutes, the display starts blinking and the transmission ends. A beep will
sound until the PTT switch (18) key is released.
19) UP/DN KEYS ON MICROPHONE
Press UP/DN keys (13) on the microphone to
increase
and DN to
decrease
See ROTARY KNOB page 7.
20) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 59.
CB
WX
mode. It does not sound in
activate/deactivate
WX
mode.
a message,
is displayed and release
disappears.
(short press)
change
the channel. UP to
the channel.
A) DC-POWER TERMINAL (13.2 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) PA SPEAKER JACK (8 Ω, Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (Ø 2.5 mm)
mode.
the ALERT
C) FUNCTIONS WITH THE PTT SWITCH
1) TALKBACK LEVEL
This function allows to adjust the volume level of the TALKBACK.
1.
Activate the TALKBACK function.
2.
Press and hold the PTT switch (18) then turn the CH rotary knob (4) to
crease
(clockwise) /
TALKBACK.
3.
Release the PTT switch (18).
D) MENU
The order of 23 menus is as described in this manual. However, the menu
displayed by entering the MENU will be the last menu modified by user.
The procedure is the same whatever the function is:
Long Press PUSH key (4) to
1.
Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
select
the menu to set.
2.
Press PUSH key (4) to
3.
Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
modify
the value of the parameter.
4.
New press on PUSH key (4) to
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5.
If no key is pressed, the unit
from the display.
Note: UP/DN keys (19) on the microphone have the same effect as the
rotation of the CH rotary knob (4). PTT switch (18)
and
exists
MENU.
1) COLOR
Long Press PUSH key (4) to
11
decrease
(counterclockwise) the volume level of the
enter
the MENU.
is displayed.
validate.
The current color blinks on the display.
validate
the chosen value. The parameter
exits
MENU after 10 seconds.
validates
disappears.
enter
the MENU.
is displayed.
in-
disappears
the last setting
Publicité
