Publicité
Les langues disponibles
Les langues disponibles
-
Frequency Modulation / FM: for nearby communications on a flat open
field.
-
Upper and Lower Side Band/ USB-LSB: used for long distance communica-
tions (according to the propagation conditions).
PA (Public Address)
(long press)
An external loudspeaker can be connected to the unit by the PA jack plug
located on the back panel PA.SP. (D). Turn the VOL knob (1) to adjust the
PA volume.
Long press MODE key (5) to
alternate
PA
For details on operating in
14.
M1
See § MEMORY page 8.
6) MEMORY ~ CTCSS/DCS ~ M2
MEMORY
(short press)
memorize
This CB radio allows you to
To store into memory:
-
Select the channel and its attributes.
-
Press the MEM key (6) for one second. If the KEY BEEP function is active, a
beep sounds. "MEM" flashes.
-
Press for one second one of the keys M1 (5), M2 (6), M3 (7) or M4 (8) to
memorize. "MEM" appears in the display and the number of the selected
memory (M1, M2, M3 or M4) flashes.
-
If the KEY BEEP function is active, a long beep confirms the success of the
operation.
To call a memory:
-
Press the MEM key (6) for one second. If the KEY BEEP function is active, a
beep sounds. "MEM" flashes.
Briefly press one of the M1 (5), M2 (6), M3 (7) or M4 (8) keys to display the
-
selected memory.
"MEM" is displayed, the number of the selected memory (M1, M2, M3 or
-
M4) flashes.
CTCSS/DCS
For simplicity, in this manual we will speak of CTCSS/DCS code to indicate
both a CTCSS tone and a DCS code, of GENRE to indicate the kind of code
CB
PA
between
and
mode.
mode, consult the PA SETTING menu page
4 channels with the following attributes.
(CTCSS, DCS or OFF = no code). TYPE indicates whether this is a TX transmis-
sion or an RX reception and MODE specifies the operating mode, Identical
I d or different DF.
Consult the CODE SET menu page 15.
See list of codes on pages 59.
Note: Codes can only be used in FM. Each channel can have its own code.
Press for one second one of the MEM key (6) to
-
CTCSS/DCS function.
Activation
If a CTCSS/DCS code has been stored, it becomes active, "CTCSS" or "DCS"
icon is displayed on the screen.
In MODE I d, if no CTCSS/DCS code has been stored, the device emits an
error beep. Go to the CODE SET menu to store a CTCSS/DCS code.
In DF MODE, if no CTCSS/DCS code has been stored in either TYPE TX or TYPE
RX, the device emits an error beep. Go to the CODE SET menu to store the
CTCSS/DCS codes.
Deactivation
If a CTCSS/DCS code has been stored and "CTCSS" or "DCS" is displayed on
the screen, a long press on the MEM key (6) deactivates the stored code,
"CTCSS" or "DCS" disappears, a deactivation beep sounds. The memorized
CTCSS/DCS code is kept in memory but no longer functions.
M2
.
See § MEMORY page 8
7) SCAN ~ DW ~ SKIP ~ M3
SCAN
(short press)
Press the SCAN/DW key (7) to
order. "SCAN" is displayed. The scanning stops as a channel is active. The
scanning automatically starts 3 seconds after the end of the transmission
and no key is activated. In
or use the UP/DN buttons (19) on the microphone to change scan direction.
(see § SKIP below)
Press the PTT switch (18) or the SCAN key (7) to
DW
(combination 14 + 7)
Short press the F key (14).
Short press the SCAN/DW key (7)
8
activate/deactivate
activate
the SCAN function in ascending
mode, turn the rotary CH knob (4)
SCANNING
exit
the SCAN function.
appears on the display,
activates
the DW (Dual Watch) function.
the
Publicité
