Publicité
Les langues disponibles
Les langues disponibles
PARAMETERS
Threshold of cycles for assistance request. Once the limit is reached the
se
r
19
next cycles will be done with fast blinking (only if FPr enabled).
.
.
0 = disabled.
Continuous blinking for assistance request (done only with closed
automation):
se
f
20
.
.
0 = disabled.
1 = enabled.
Mode of use of the R1 output (plug-in):
0 = output not used.
rI
m
21
.
.
1 = courtesy light (copy of the control unit output).
2 = ECOMODE.
mp
r
22
Pressure of the motor in closed position.
.
.
mr
e
23
Function for the mechanical relaxation of the motor.
.
.
Restore default settings depending on the motor type:
0 = CUSTOM
1 = KALOS XL / MOVEO
de
f
24
2 = KALOS 70
.
.
3 = KALOS 110
4 = SIM
5 = KALOS XL FAST / MOVEO FAST
tr
s
25
Viewing of the memory location for a single transmitter.
.
.
tr
C
26
Cancellation of a single transmitter.
.
.
Cancelling all transmitters. Enter to modify the parameter and then keep
tr
f
27
pressed the "MENU" button, a count down appears that ends with don on
.
.
the display.
sI
d
28
First coupling between Bluetooth device and control unit.
.
.
WARNING - do not use on the sliding motors.
1
These values are not suggested for the sliding motors.
2
NOTE - the parameters highlighted in grey depend on the selected motor. On the table are reported the data of the CUSTOM motor. For more
information, refer to chapter 11.
1.
MODE OF THE SENSOR INTERVENTION Sn.M.
It is possible to select 4 intervention types for the current sensor that detect the motor blocked:
•
sn.m. = 0 sensor is disabled.
•
sn.m. = 1 complete functioning: intervention for obstacle detection in the central zone of the stroke and intervention for the ends of the movement
in the areas near the limit switch. Do not use with sliding gates.
•
sn.m. = 2 the sensor intervenes only for obstacle detection in any position.
sn.m. = 3 the sensor intervenes only as end of the movement in any position. Do not use with sliding gates.
•
2.
INTERVENTION TIME OF THE SENSOR SI.T.
Time after which intervenes the sensor for the motor blocked detection (current sensor) with an obstacle.
3.
DISABLING TIME DURING THE START OF THE MOTOR Sd.T.
Time in which the current sensors is disabled during the start of the motor.
4.
ACCELERATION RAMP UR.A.
This parameter allows to set the acceleration ramp amplitude during the start of the motor. Higher is the value and longer will be the ramp. With Ur.A.
= 0, the ramps are disabled and the motor starts directly at the running speed or at the slowdown speed, depending on the position during the stroke.
In addition to the numerical values, there are 2 additional options:
•
SS.r. - the motor starts at the 50% of the running speed for 0,6 seconds.
•
HS.r. - the motor starts at the 100% of the running speed for 0,6 seconds.
5.
DECELERATION RAMP dr.A.
This parameter allows to set the deceleration ramp amplitude from the running speed to the slowdown speed. Higher is the value and longer will be
the ramp.
6.
FUNCTIONING OF PH1 FROM CLOSED POSITION SP.h.
The closing photocell has the following functioning:
•
Closing: immediate inversion of the movement.
•
Opening from an intermediate position: no intervention.
•
Opening from closed position:
– Sp.h. = 0 the automation doesn't move if PH1 beam is cut.
– Sp.h. = 1 the automation moves while PH1 beam is cut.
7.
FUNCTIONING OF PH2 Ph.2.
16/20
All manuals and user guides at all-guides.com
DESCRIPTION
2
2
ITA
ENG
FRA
DEFAULT
CUSTOM
0
0
1
0
0
0
ESP
6-1622400 rev. 5
MIN
MAX
UNIT
x 1000
0
100
cycles
0
1
0
1
0
480
min
0
10
x 50ms
0
5
04/06/2019
Publicité
