Wisniowski ST-2 Notice De Montage Et De Fonctionnement page 4

EN
EXTENDED INSTRUCTION OF ST-2 STEERING UNIT
WARNING! The driver is powered from power
network and protected by 6,3 A-F fuse.
Changing the fuse value or type can cause
permanent damage to the driver!
I. DESTINATION
The steering unit is designed to control the gates with ~ 24V installation. Giving
the opportunity to save 60 remote controls in memory (optionally up to 470)
and having wired control (using buttons) the steering unit is perfectly suitable for
use in sealed settlements, guarded parking lots and business parking lots.
II. STEERING UNIT OPERATION
The steering unit starts opening or closing the gate after it receives a signal from
the remote control or a button. The first move after connecting gate, when the
steering unit is not calibrated is carried out with full speed. In order to perform
the automatic calibration the gate has to perform a full opening. Calibration
involves measuring the length of the gate. After completing the calibration, at
50cm before closing or full opening the gate, the steering unit decreases gate
speed in order to reduce force levels on possible obstacle.
Connected to the steering unit light indicator flashes when the gate moves. It
also indicates with 6 seconds advance the start of the automatic gate closing.
Re-calibration can take place automatically when the gate is moved manually
while the steering unit is powered.
III. DRAWING OF THE CENTRAL UNIT AND THE EXTENSION
BOARD OF THE ST-2 STEERING UNIT
ST-2 GATE STEERING UNIT
4
Assembly and Operating Instructions - ST-2 sliding gate steering unit
Fig. 1
IV. SPECIFICATION AND CONNECTORS DESCRIPTION OF THE
ST-2 STEERING UNIT
The steering unit central unit is placed in transparent case of
class. The wires from the case are protected by PG-11cable adaptor of
containment class.
1. Specification
Central unit + extension board
Supply voltage
Min current (standby)
Max current (standby)
Max current (24V ~ )
Temperature range
The steering unit power input is protected by
Variable code remote control
Working frequency
Supply voltage
Current
Battery type
Modulation type
2. Connectors description
+10%
1, 2 Power input 24V ~ 50Hz
3, 4 Light indicator output - max power
5, 6 steering unit motor output -
(short-circuit protected)
7-11 control inputs (NC/NO), absolute maximum voltage +/-35V
7. STER2 - control input 1 (active - GND (NO)). Corresponds
to the first button on the remote control. Opens the
gate when "HOLD TO RUN" function is active.
8. STER1 - pedestrian gate function control input (active -
GND (NO)). Corresponds to the second button on
the remote control. Closes the gate when "HOLD
TO RUN" function is active.
9. KRANC1 - gate open detector input
P
Active no GND - NC (default settings)
P
Active GND - NO
10. COM (GND) - GND output
11. KRANC2 - gate close detector input
P
Active no GND - NC (default settings)
P
Active GND - NO
12-14 - w control inputs (NC/NO), absolute maximum voltage +/-35V
12. STOP2 - input for stopping the gate (active no GND (NC))
13. BARIERA - the barrier input (active no GND (NC))
14. STOP1 - parametric input for stopping the gate. Parameter is
8.2K. input detects parameter change more than
+100% (16.4K ) or less than
15. COM (GND) - GND output
Anntena - connector for additional antenna mounted in
column
" CANCEL ",
"(-)", "(+)", "OK" - configuration buttons
OUTPUT ~ 24V - Aux power output for additional devices.
V. MAIN FEATURES
P
Automatic stop when the gate area of work is violated (barrier).
P
Pedestrian gate function.
P
Automatic closing the gate after opening (optional).
P
Delayed start and stop of the gate.
P
Remote controls support up to 60 in standard version. Available versions
for up to:
- 170 remote control,
- 270 remote control,
- 370 remote control,
- 470 remote control.
P
"HOLD TO RUN" function.
P
"SETTLEMENT" function.
P
The ability to selectively program and erase remote controls.
P
The ability to easily program remote controls using the button on the
extension board (optional).
P
Two STOP inputs for immediate gate halt.
P
Numeric display showing:
- State of the steering unit: closing the gate, opening the gate, fast move,
slow move, gate halt during opening or closing with an indication of the
reasons of the halt event.
IIiO/ST-2/12/2013/ID-91384 Technical Documentation
IP66
containment
+10%
24V ~ 50Hz /
-15%
+15%
130mA /
-15%
+15%
200mA /
-15%
7,7A
- 30°C ÷ +85°C
6,3A F (fast) fuse
433,92Mhz ±100kHz
( ambient temp 25°C)
+12V
4 ÷ 6 mA
A23
FSK
/
-15%
25W ( short-circuit protected )
24V DC motor with 7,7A max current
W W
- 75% (2K ) .
.
P
IP54