Wisniowski ST-2 Notice De Montage Et De Fonctionnement page 2

EN
TABLE OF CONTENTS
SHORT CUT INSTRUCTION OF ST-2 STEERING UNIT
I. INSTALLATION ........................................................................................... 2
II. EASY REMOTE CONTROLS PROGRAMMING ...................................... 2
III. PEDESTRIAN GATE FUNCTION ............................................................... 3
IV. AUTOMATIC GATE CLOSING ................................................................. 3
V. ENTERING THE INSTALLER CODE ........................................................... 3
EXTENDED INSTRUCTION OF ST-2 STEERING UNIT
I. DESTINATION ............................................................................................ 4
II. STEERING UNIT OPERATION .................................................................. 4
III. DRAWING OF THE CENTRAL UNIT AND THE EXTENSION
BOARD OF THE ST-2 STEERING UNIT .................................................... 4
IV. SPECIFICATION AND CONNECTORS DESCRIPTION OF THE ST-2
STEERING UNIT ............................................................................................... 4
1. Specification .......................................................................................... 4
2. Connectors description ......................................................................... 4
V. MAIN FEATURES ........................................................................................ 4
VI. OPERATING THE GATE ............................................................................. 5
1. Opening and closing the gate ............................................................. 5
2. Pedestrian gate function ....................................................................... 5
3. Automatic gate closing ......................................................................... 5
4. Barrier function ...................................................................................... 5
5. "HOLD TO RUN" function ................................................................... 6
6. "SETTLEMENT" function ....................................................................... 6
7. Light indicator ........................................................................................ 6
8. Operating 2 gates using the same set of remote controls ................. 6
9. Overload protection ............................................................................. 6
9.1. Dynamic protection („dn") .......................................................... 6
9.2. Static protection („St") ................................................................ 7
9.3. Automatic dynamic and static overload protection
configuration ................................................................................ 7
9.4. Procedure of stopping the gate after overload ......................... 7
10. Lifetime counters ................................................................................... 7
VII. DISPLAYED MESSAGES ...................................................................................... 7
VIII. INSTALLATION AND FIRST RUN ............................................................. 8
IX. CONFIGURATING THE STEERING UNIT ............................................... 9
X. STEERING UNIT PROGRAMMING MODE ......................................... 10
1. Easy remote controls programming .................................................. 10
2. Entering the installer code .................................................................. 10
3. Changing installer code ..................................................................... 10
4. Static overload protection .................................................................. 10
5. Dynamic overload protection ............................................................ 10
6. Automatic overload protection configuration ................................... 11
7. Resetting the steering unit calibration ................................................ 11
8. Pedestrian gate function ..................................................................... 11
9. Operating 2 gates .............................................................................. 11
10. Setting the lamp on time after closing/opening the gate ............... 11
11. Remote controls ................................................................................... 11
11.1. Programming new remote controls .......................................... 12
11.2. Erasing remote controls ............................................................ 12
11.3. Checking the number of free positions in the memory .......... 12
12. The barrier ........................................................................................... 12
12.1. Changing the barrier function operation mode ..................... 12
12.2. Changing the barrier function state ........................................ 12
13. Automatic gate closing ...................................................................... 12
14. "SETTLEMENT" ................................................................................... 13
15. "HOLD TO RUN" .............................................................................. 13
16. Number of closings ............................................................................ 13
17. Number of openings .......................................................................... 13
18. Number of stops during closing ........................................................ 13
19. Number of stops during opening ...................................................... 13
20. Damage report ................................................................................... 13
21. Restoring factory settings ................................................................... 14
W
22. Parametrical (8.2K ) STOP1 input ................................................. 14
23. STOP2 input (active - no GND) ........................................................ 14
24. Checking the number of remote controls allowed by license ........ 14
25. Changing easy remote controls programming function state ........ 14
ST-2 STEERING UNIT PROGRAMMING DIAGRAM MODE
2
Assembly and Operating Instructions - ST-2 sliding gate steering unit
........................ 2
.......................... 4
............... 15
SHORT CUT INSTRUCTION OF ST-2 STEERING UNIT
I. INSTALLATION
1. Turn off the power supply.
2. Pull out the fast-connectors.
3. Connect the wires to fast-connectors according to notice signed on
connecting board:
P
Supply of the steering input 1-2, marked as input ~ 24V.
P
Manual steering (option) input 7-15.
P
External antenna (option).
P
Signaling lamp (option) input 3-4.
P
Infrared barrier (option) input 13-15 (set up as active by the producer, the
continuous work of a circuit is secured by the hardware jumper) plus
photo-cells supply marked as output ~ 24V. Before installing of the
Photocells contacts remove the hardware jumper.
There are 4 operations modes of the BARRIER FUNCTION:
P
breaching the barrier during gate opening and closing stops the gate,
P
breaching the barrier during gate opening stops the gate. In contrast,
during gate closing is stops the gate and after a moment the full opening
is performed,
P
breaching the barrier during gate closing stops the gate,
P
breaching the barrier during gate closing stops the gate and after a
moment the full opening is performed,
NOTE: The barrier function is disabled by factory
default to mode number 4.
To change setting of the barrier mode check the
advanced manual.
The barrier input is GND active input (NC).
4. Connect fast-connectors.
5. Set manually the gate in the middle.
6. Turn on the power supply.
7. Check if the limit switches are properly stopping the drive unit. If not
change the place of connecting.
8.Adjust the overload power. Proceed as follows:
Automatic overload protection configuration
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "PA" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message showing current working state ("on" - enabled, "of" - disabled)
will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
9. Initiate two cycles open close of the gate to calibrate times of the steering
unit. This actions are to set the moment of stopping the drive unit and set
the static and dynamic overload power.
10. Check if the drive unit works properly and set additional options (if
required). Proceed as follows.
II. EASY REMOTE CONTROLS PROGRAMMING
The easy remote programming feature is enabled by factory default
("PC" = on). In order to program new remote control press "OK" button for
6 seconds until message "Pr" appears on the display and the lamp blinks.
Then press any button on the remote control you would like to program. The
number of the newly programmed remote control would appear on the
display.
The steering unit automatically leaves the easy remote controls programming
function 5 seconds after programming last remote control.
In order to erase all remote controls which are in memory of the steering unit,
the "OK" button should be pressed and hold for 10 seconds. The lamp will
light up on permanently and blinking message "Pr" will appear on the
display. Then, after 5 seconds the light will blink and new remote controls
can be programmed.
To disable or enable this function Look
è
mode Changing easy remote controls programming function
state .
IIiO/ST-2/12/2013/ID-91384 Technical Documentation
è
Steering unit
).
è
Steering unit programming
P