Wisniowski ST-2 Notice De Montage Et De Fonctionnement page 14

EN
è
programming mode Entering the installer code
P
Select "Er" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Messages indicating particular type of damage may be displayed sequentially:
1. "tr" - slow move module damaged,
2. "SL" - motor short circuit,
3. "CL" - gate close detector damaged,
4. "OP" - gate open detector damaged.
NOTE: No message displayed means no damage
detected.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
21. Restoring factory settings
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "FA" function using (+), (-) buttons,
P
Press "OK" 5 times to restore factory settings,
P
After first pressing "OK" button the two dots will light and disappear after
the fifth pressing,
Factory default settings are listed below:
- Static overload protection max current ("St") = 3,6A
- Dynamic overload protection max current step("dn") = 1,8A
- The installer security code = 1234
- Pedestrian gate width ("Fr") = 5
- Lamp after closing/opening the gate disabled ("tl") = 0.0min
- The barrier operations mode ("bA") = 4
- Automatic gate closing disabled ("Au") = 0
- SETTLEMENT function disabled ("Os") = of
- HOLD TO RUN function disabled ("Hr") = of
- Parametrical STOP1 input disabled ("SP") = of
- STOP2 input ("SE") = of
- Analysis barrier insert set to on, „Sb" = on
- Damage reports will be reset ("Er")
- The gate calibration will be reset ("cr")
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
W
22. Parametrical (8.2K ) STOP1 input
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "SP" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message showing current working state ("on" enabled, "of" - disabled)
will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
23. STOP2 input (active - no GND)
P
Enter steering unit programming mode (Look
14
Assembly and Operating Instructions - ST-2 sliding gate steering unit
).
è
S teering unit
),
è
Steering unit
).
è
Steering unit
è
programming mode Entering the installer code
P
Select "SE" function using (+), (-) buttons.
P
Press "OK" to accept selection
P
Message showing current working state ("on" enabled, "of" - disabled)
will appear on the display
P
Use (+), (-) buttons to select new value
P
Press "OK" to save new setting or "CANCEL" to return
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
24. Checking the number of remote controls allowed by license
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "LC" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message "P" and number of remote controls allowed by the license will
be shown sequentially
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
25. Changing easy remote controls programming function state
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Pc" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message showing current working state ("on" enabled, "of" - disabled)
will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
IIiO/ST-2/12/2013/ID-91384 Technical Documentation
).
è
Steering unit
).
è
Steering unit
).
P