Wisniowski ST-2 Notice De Montage Et De Fonctionnement page 3

III. PEDESTRIAN GATE FUNCTION
CAUTION! The wicket function is set as active by
the producer.
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Fr" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Number between 1 and 15 or "0"
"0" - function is disabled
does not work. The button No. 1 and both wired buttons cause full
opening or closing the gate.
"- -" - function is disabled
control are swapped. The button No. 1 does not work. The button No. 2
and both wired buttons cause full opening or closing the gate. This setting
can be helpful during 2 gates operation mode.
Number between 1-15 function is enabled
the width of the gate expressed in sixteenth parts of the full width of the
gate (for example 4 means 4/16* of the width of fully opened gate that
is about 25% of the gate width).
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
*) 4/16*4m = 1m
IV. AUTOMATIC GATE CLOSING
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Au" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Number between 0.0 - 9.9 will appear on the display.
Value 0.0 indicates that the function is disabled and the gate should be
closed using button or remote control.
Value between 0.1 - 9.9 indicates the time (in minutes) after which
automatic gate closing will start after opening the gate.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
V. ENTERING THE INSTALLER CODE
Entering the steering unit programming mode is possible after entering the
installer code. Please note that the gate must be fully opened or closed and
not moving.
WARNING! During steering unit programming mode
buttons and remote controls cannot move the gate.
NOTE: Factory default installer code is 1234, and the
following example shows entering procedure of this
code.
P
Press any key (CANCEL, (+), (-), OK).
Message " 00. " will appear on the screen:
P
Enter the first digit of the installer code (1) using (+), (-) buttons.
Message " 01. " will appear on the screen.
NOTE: The lighting dot on the display indicates
selected digit.
P
Press "OK" to accept selection.
P
Enter the second digit of the installer code (2) using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message " 2.1 " will appear again on the screen and the last 2 digits can
be entered the same way.
P
Enter the third digit of the installer code (3) using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Technical Documentation IIiO/ST-2/12/2013/ID-91384
Assembly and Operating Instructions - ST-2 sliding gate steering unit
è
Steering unit
).
or "- -" will appear on the screen:
. The button No. 2 on the remote control
. Buttons No. 1 and No. 2 on the remote
. The value indicates
è
Steering unit
).
P
Enter the fourth digit of the installer code (4) using (+), (-) buttons.
P
Press "OK" to accept selection.
The steering unit will enter steering unit programming mode.
In this mode the user can change all available parameters of the device.
(+), (-) buttons are used to select functions.
P
OK button is used to accept selection.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
Photocells
power supply
Steering unit
Signaling
power supply
lamp
~ 24 [V]
EN
Photocells
steering Input
3