Wisniowski ST-2 Notice De Montage Et De Fonctionnement page 13

P
Press "OK" to accept selection.
Number between 0.0 - 9.9 will appear on the display.
P
Value 0.0 indicates that the function is disabled and the gate should be
closed using button or remote control.
P
Value between 0.1 - 9.9 indicates the time (in minutes) after which
automatic gate closing will start after opening the gate.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
14. "SETTLEMENT"
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "oS" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message showing current working state ("on" - enabled, "of" - disabled)
will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
NOTE: The settlement function is disabled by
factory default.
15. "HOLD TO RUN"
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Hr" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message showing current working state ("on"- enabled, "of" - disabled)
will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
NOTE: The "HOLD TO RUN" function is disabled by
factory default.
è
Steering unit programming mode
stops during closing.
è
Steering unit programming mode
stops during opening.
P
Technical Documentation IIiO/ST-2/12/2013/ID-91384
Assembly and Operating Instructions - ST-2 sliding gate steering unit
è
S teering unit
).
è
Steering unit
).
è
Number of
è
Number of
16. Number of closings
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "cc" function using (+), (-) buttons.
P
After selecting "cc" function the number of full closings will be displayed
sequentially (in this example the gate closed 515 times),
P
press (+) or "OK" to show number of openings,
P
press (-) or "CANCEL" to select the previous function.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
17. Number of openings
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "co" function using (+), (-) buttons.
P
After selecting "co" function the number of full openings will be displayed
sequentially (in this example the gate opened 416 times),
P
press (+) or "OK" to show number of stops during closing,
P
press (-) or "CANCEL" to select the previous function.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
18. Number of stops during closing
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Pc" function using (+), (-) buttons.
P
After selecting "co" function the number of stops during closing will be
displayed sequentially (in this example the gate stopped during closing
16 times).
P
press (+) or "OK" to show number of stops during opening.
P
press (-) or "CANCEL" to select the previous function.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
19. Number of stops during opening
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Po" function using (+), (-) buttons.
P
After selecting "co" function the number of stops during opening will be
displayed sequentially (in this example the gate stopped during opening
16 times).
P
press (+) or "OK" to select the next function.
P
press (-) or "CANCEL" to select the previous function.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
20. Damage report
P
Enter steering unit programming mode (Look
EN
è
Steering unit
).
è
Steering unit
).
è
Steering unit
).
è
Steering unit
).
è
Steering unit
13