Wisniowski ST-2 Notice De Montage Et De Fonctionnement page 12

EN
can be erased individually so that lost or stolen remote controls can be easily
removed from memory.
11.1. Programming new remote controls
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Pr" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Use (+) (-) buttons to select the number of position in memory.
NOTE: Blinking number means that selected memory
position is free and can be used to save a new remote
control, while numbers which light continuously
indicate positions that are currently under use.
P
Press any button on the remote control to let the steering unit to read ID
code of the remote control.
- The number will stop blinking after programming the remote control.
- If the remote control is already in memory, it will not be programmed
again. The display will show for 2 seconds the number of position
where the remote control is programmed.
- If the current selected position is occupied the steering unit will
automatically find the next free position and program the remote
control.
- To use occupied position it must be erased first by pressing "OK"
è
button 5 times (Look Steering unit programming mode
Erasing remote controls ).
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
NOTE: When using high number of remote controls it
may be helpful to record users data and assign it to
specified numbers of remote controls in case of
remote control loss and need to erase it from
memory without having to erase all remote controls.
11.2. Erasing remote controls
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Pr" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Use (+) (-) buttons to select the number of position in memory to be
erased.
P
Press "OK." button 5 times.
After first pressing "OK" button the two dots will light.
After erasing the number will start blinking indicating the position is now free
To erase another remote control use (+) (-) buttons to select its position in
memory and repeat the procedure.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
11.3. Checking the number of free positions in the memory
This feature allows you to check the number of free positions for remote
controls in the memory, and also allows you to erase all programmed remote
controls.
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Pf" function using (+), (-) buttons.
12
Assembly and Operating Instructions - ST-2 sliding gate steering unit
è
Steering unit
).
è
è
S teering unit
).
è
Steering unit
).
P
Press "OK" to accept selection.
P
The display will show the number of free positions in the memory.
P
To erase all programmed remote controls press "OK." button 5 times:
- After first pressing "OK" button the two dots will light.
- After erasing the total number (all free) of positions it the memory will
appear on the display.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
12. The barrier
There are four operations modes of the Barrier function:
P
breaching the barrier during gate opening and closing stops the gate,
P
breaching the barrier during gate opening stops the gate. In contrast,
during gate closing is stops the gate and after a moment the full opening
is performed,
P
breaching the barrier during gate closing stops the gate,
P
breaching the barrier during gate closing stops the gate and after
a moment the full opening is performed.
NOTE: The barrier function is disabled by factory
default. The barrier function default operation
mode is 4 by. Enabling the barrier function will
automatically set the function to mode 4 regardless
the previous settings.
The barrier input is GND active input (NC). Insert "Barrier" is the NC insert.
Responds to the lack of the supply common. It's been set as active by the
producer. To change the setting of this function go to "Sb" function.
12.1. Changing the barrier function operation mode
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "bA" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Number of current working mode (1-4) will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
12.2. Changing the barrier function state
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
Select "Sb" function using (+), (-) buttons.
P
Press "OK" to accept selection.
P
Message showing current working state ("on" - enabled, "of" - disabled)
will appear on the display.
P
Use (+), (-) buttons to select new value.
P
Press "OK" to save new setting or "CANCEL" to return.
P
To return to normal operation press "CANCEL" button as many times until
the one of the messages described in paragraph "DISPLAYED
MESSAGES" will appear on the display.
13. Automatic gate closing
P
Enter steering unit programming mode (Look
è
programming mode Entering the installer code
P
"Au"
Select function using (+), (-) buttons.
IIiO/ST-2/12/2013/ID-91384 Technical Documentation
è
S teering unit
).
è
Steering unit
).
è
Steering unit
).
P