Publicité
Les langues disponibles
Les langues disponibles
36 | Section
CHEMICAL BALANCE,
It is wise to test pool water regularly. Never allow chlorine residual to drop below 0.6 ppm (parts per million). The
minimum level for effective chlorine or bromine residual is 1.4 ppm.
pH - The term pH refers to the acid/alkaline balance of water expressed on a numerical scale from 0 to 14. A test kit for measuring
pH balance of your pool water is available from your local pool supply store; see Table 6.
Muriatic Acid has a pH of about 0. Pure water is 7 (neutral). Weak Lye solution have a pH of 13-14.
RULE: 7.4 to 7.6 is a desirable pH range. It is essential to maintain correct pH, see Table 6.
If pH becomes too high (over alkaline), it has these effects:
1. Greatly lowers the ability of chlorine to destroy bacteria and algae.
2.
Water becomes cloudy.
3.
There is more danger of scale formation on the plaster or in the heat exchanger tubing.
4.
Filter elements may become blocked.
If pH is too low (over acid) the following conditions may occur:
1.
Excessive eye burn or skin irritation.
2.
Etching of the plaster.
3.
Corrosion of metal fixtures in the filtration and recirculation system, which may create brown, blue, green, or sometimes almost
black stains on the plaster.
4.
Corrosion of copper tubes in the heater, which may cause leaks.
5.
If you have a sand and gravel filter, the alum used as a filter aid may dissolve and pass through the filter.
CAUTION: Do not test for pH when the chlorine residual is 3.0 ppm or higher, or bromine residual is
6.0 ppm or higher. See your local pool supply store for help in properly balancing your water chemistry.
RULE: Chemicals that are acid lower pH. Chemicals that are alkaline raise pH.
ALKALINITY High or Low:
"Total alkalinity" is a measurement of the total amount of alkaline chemicals in the water, and control pH to a great degree. (It is not the
same as pH which refers merely to the relative alkalinity/acidity balance.) Your pool water's total alkalinity should be 100 - 140 ppm to
permit easier pH control.
A total alkalinity test is simple to perform with a reliable test kit. You will need to test about once a week and make proper adjustments
until alkalinity is in the proper range. Then, test only once every month or so to be sure it is being maintained. See your local pool dealer
for help in properly balancing the water chemistry.
WATER CHEMISTRY PARAMETERS
Disinfectant levels
Free Chlorine, ppm
Combined Chlorine, ppm
Bromine, ppm
Other Sanitizers
Chemical Values
pH
Total Alkalinity (Buffering), ppm
as CaCO3
Salt
Total Dissolved Solids, ppm
Calcium Hardness, ppm, as CaCO3
Heavy Metals
Biological Values
Algae
Bacteria
NOTICE: Failure to adhere to the listed water chemistry parameters may result in premature failure of the heat exchanger and will void the warranty.
*Start-up TDS includes source water TDS and any other inorganic salt added at start-up.
™
MASTERTEMP
Pool and Spa Heater Installation and User's Guide
All manuals and user guides at all-guides.com
(continued)
Minimum
1.0
None
2.0
Levels not established. Consult local health department before use.
7.2
60
2000
N/A
150
None
None
None
Section 4. Maintenance Instructions
Ideal
2.0-4.0
None
4-6
7.4-7.6
80-100
3200
N/A
1,500 ppm > TDS at startup*
200-400
None
None
None
Refer to Local Code
Table 6.
Maximum
5.0
0.2
10.0
7.8
180
5000**
500-1,000
None
None
P/N 475106 Rev. D 1/2016
Publicité
