Motorola Solutions MTP8 Serie Mode D'emploi page 3

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 117
Operational Cautions for Intrinsic Safe Equipment
The radio units must be ordered with the intrinsic safety option and shipped from the Motorola Solutions manufacturing facility with
the hazardous location certification label. Radio will not be upgraded to this capability or labeled once they have been shipped.
DO NOT charge the batteries inside potentially hazardous atmosphere. Only charge batteries outside of hazardous atmosphere.
DO NOT disconnect or change the batteries inside potential hazardous atmosphere. The batteries have to remain attached to the
C a u t i o n
radios in hazardous atmosphere.
DO NOT change SIM or SD cards in hazardous atmosphere. Ensure that the SIM card door is present and secured before
entering a hazardous atmosphere.
SIM card Door screws must be secured with a torque of 0.18 to 0.22 Nm or 1.6 to 2.0 lbf-In.
Use only approved microSD devices listed in the section "Approved Accessories" on page 5. Only use mini SIM cards with
physical/electrical characteristics per ISO 7816 part 1 to 3.
Use only ATEX / IECEx approved accessories in potentially hazardous atmosphere as listed in the section "Approved
Accessories" on page 5.
Use only INMETRO (Brazil) approved accessories in potentially hazardous atmosphere as listed in INMETRO certification.
Check the hazardous location classification of the accessories. The system of the radio and accessory is only protected to the
lowest classification of both.
When the radio is used in a hazardous area, it is mandatory that either the protective cover 0104063J98 or an ATEX / IECEx
approved accessory is fitted at the accessory connector.
When the radio is used in a hazardous area, it is mandatory that either the protective cover 0104063J98 or an INMETRO (Brazil)
approved accessory is fitted at the accessory connector.
Ensure that only antennas listed in the Approved Accessories section are used in the potentially hazardous atmosphere.
Change accessories, antennas or the dust cover only outside of hazardous environment in a dust free and dry environment.
Check that the accessory connector area is in good condition (dry and free of dust).
Fasten the accessory connector, antenna, and dust cover tightly to the radio before entering potentially hazardous atmosphere.
DO NOT operate radio communications equipment in potentially hazardous areas unless it is certified as intrinsically safe. This
could result in unsafe condition in hazardous areas. DO NOT use the unit in hazardous areas if it has been physically damaged
(for example: cracked housing, water intrusion, damaged antenna). The intrinsic safety rating will be compromised and could
result in unsafe condition in hazardous areas.
DO NOT clean the radios and batteries when used in an environment with gas exposure.
Ensure the radios are operating as intended before entering a hazardous area.
Failure to use a Motorola Solutions intrinsically safe battery or accessories that are specifically certified for that radio unit negates
the certification rating and could result in unsafe condition in hazardous areas.
DO NOT disassemble an intrinsically safe product in any way that exposes the internal circuits of the unit. This could result in
unsafe condition in hazardous areas.
Servicing and repair must only be performed by Motorola Solutions trained service personnel or a Motorola Solutions-authorized
service organization, to ensure continued compliance of our ATEX / IECEx certified radios.
Servicing and repair must only be performed by Motorola Solutions trained service personnel or a Motorola Solutions-authorized
service organization, to ensure continued compliance of our INMETRO (Brazil) certified radios.
Unauthorized modification, or incorrect repair or service to the intrinsically safe product could adversely affect the certification
rating and result in unsafe condition in hazardous areas.
DO NOT add labels to the external enclosure of the radio, battery or antenna other than the approved color rings and back cover
identification kit, PMHN4297A listed on the following page.
It is not allowed to operate the radio with a missing Back cover identification kit, PMHN4297A in hazardous areas.
Use of non-Motorola Solutions parts or substitution of parts voids the intrinsic safety approval rating of the Motorola Solutions unit
and could result in unsafe condition in hazardous areas.
3
English

Publicité

Table des Matières
loading

Table des Matières