Briggs & Stratton VANGUARD 130000 Manuel D'utilisation page 10

3. If the fuel strainer is dirty, clean or replace it. If you replace the fuel strainer, make
sure to use an original equipment replacement fuel strainer.
Service Cooling System
WARNING
Running engines produce heat. Engine parts, especially muffler, become extremely
hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc., can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
NOTICE Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
1. Use a brush or dry cloth to remove debris from the air intake grille.
2. Keep linkage, springs and controls clean.
3. Keep the area around and behind the muffler, if equipped, free of any combustible
debris.
4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.
After a period of time, debris can accumulate in the cylinder cooling fins and cause the
engine to overheat. This debris cannot be removed without partial disassembly of the
engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air
cooling system as recommended in the Maintenance Schedule.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have pilot
lights or other ignition sources because they can ignite fuel vapors.
Fuel System
See Figure: 19
Store the engine level (normal operating position). Fill fuel tank (A, Figure 19) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits
to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs
& Stratton Advanced Formula Fuel Treatment & Stabilizer, available wherever Briggs
& Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for two (2) minutes to circulate the stabilizer throughout the
fuel system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil. See the Change Engine Oil section.
Troubleshooting
For assistance, contact your local dealer or go to VanguardEngines.com or call 1-800-
999-9333 (in USA).
10
Specifications
Model: 130000
Displacement
Bore
Stroke
Oil Capacity
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Model: 190000
Displacement
Bore
Stroke
Oil Capacity
Gear Reduction Oil Type
Gear Reduction Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily at
an angle up to 15°. Refer to the equipment operator's manual for safe allowable operating
limits on slopes.
Service Parts - Model: 130000, 190000
Service Part
Foam Air Filter (Model 130000, Figure 14)
Paper Air Filter (Model 130000, Figure 15)
Pre-cleaner (Model 130000, Figure 15)
Paper Air Filter (Model 190000, Figure 15)
Pre-cleaner (Model 190000, Figure 15)
Paper Air Filter (Figure 16)
Pre-cleaner (Figure 16)
Advanced Formula Fuel Treatment & Stabilizer
Resistor Spark Plug
Spark Plug Wrench
Spark Tester
We recommend that you see any Briggs & Stratton Authorized Dealer for all maintenance
and service of the engine and engine parts.
Power Ratings: The gross power rating for individual gasoline engine models is labeled
in accordance with SAE (Society of Automotive Engineers) code J1940 Small Engine
Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque
values are derived at 2600 RPM for those engines with "rpm" called out on the label and
3060 RPM for all others; horsepower values are derived at 3600 RPM. The gross power
curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken
with exhaust and air cleaner installed whereas gross power values are collected without
these attachments. Actual gross engine power will be higher than net engine power and
is affected by, among other things, ambient operating conditions and engine-to-engine
variability. Given the wide array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not limited to, the
variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel
12.48 ci (205 cc)
2.688 in (68,28 mm)
2.200 in (55,88 mm)
20 - 22 oz (,59 - ,65 L)
80W-90
4 oz (,12 L)
.030 in (,76 mm)
180 lb-in (20 Nm)
.010 - .014 in (,25 - ,36 mm)
.004 - .006 in (,10 - ,15 mm)
.009 - .011 in (,23 - ,28 mm)
18.63 ci (305 cc)
3.120 in (79,24 mm)
2.438 in (61,93 mm)
26 - 28 oz (,77 - ,83 L)
SAE 30
12 oz (,35 L)
.030 in (,76 mm)
180 lb-in (20 Nm)
.010 - .014 in (,25 - ,36 mm)
.004 - .006 in (,10 - ,15 mm)
.004 - .006 in (,10 - ,15 mm)
Part Number
797378
797033
798513
797032
798795
474279
491435S
100117, 100120
491055
19576, 5402
19368
VanguardEngines.com