Cleaning / Replacing The Air Filter; Checking / Replacing The Spark Plug; Checking The Ignition Spark; Silencer / Exhaust Outlet - ATIKA ASP 11 N Notice Originale - Consignes De Sécurité - Pièces De Rechange

Masquer les pouces Voir aussi pour ASP 11 N:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 38
Do not use any other types of oil. The use of any other
type of oil will adversely affect the operation of the
hydraulic cylinder.

Cleaning / replacing the air filter (36)

Clean the air filter from dust and dirt on a regular basis to
prevent
starting problems,
loss of output,
too high fuel consumption.
Clean the air filter every 25 operating hours, or more
frequently in dusty environments.
1. Loosen the screw and remove the cover (29).
2. Remove the holding clamp (37) and the foam air filter
(36) from the cover.
3. Clean holding clamp, cover and air filter plate (37).
4. Wash the foam air filter using water and liquid cleaner.
5. Squeeze the air filter in a dry and clean cloth.
6. Allow the air filter to dry well.
7. Install the air filter and the holding clamp in the cover.
8. Re-mount the cover.
Replace the air filter on a regular basis.
Damaged air filters must be replaced without delay.

Checking / replacing the spark plug (38)

Do not touch the spark plug or the spark plug connector
while the engine is running. High voltage!
Risk of burning on the hot engine. Wear protective
gloves.
Check the spark plug and the spark gap on a regular basis.
For this proceed as follows:
1. Allow the engine to cool down.
2. Remove the air filter cover (29).
3. Pull the spark plug connector (35) from the
spark plug.
4. Remove the spark plug using the supplied
spark plug wrench (39).
5. Clean the spark plug when it is contaminated.
6. The electrode gap must be 0.76mm.
7. Install the spark plug in reverse order.
Do not overtighten the spark plug.
Replace the spark plug:
every 100 hours or each season (whichever case comes
first)
when the insulating body is damaged,
when the electrodes show excessive erosion,
when the electrodes show excessive dirt or oil.
Use the following spark plug type:
Champion RC12YC
or equivalent types
All manuals and user guides at all-guides.com

Checking the ignition spark

1. Allow the engine to cool down.
2. Remove the air filter cover (29).
3. Pull the spark plug connector (35) from the spark
plug (38).
4. Remove the spark plug using the supplied spark plug
socket spanner (39).
5. Firmly connect the spark plug connector.
6. Adjust the engine as described in "Before starting the
engine".
7. Use an insulated pair of tongs to press the spark plug
against the engine body (away from the spark plug hole).
8. Firmly pull the cranking rope on the cranking handle.
A spark between the electrodes is a sign of proper
functioning

Silencer / exhaust outlet

Check the silencer regularly.
Clean the exhaust outlet (27) on a regular basis.

Oil change

Change the oil as long as the engine is still warm.
The oil must be changed after the first 5 operating hours.
Then, only every 100 operating hours or once in a season.
Two persons are required.
1. Loosen the oil drain plug (34).
2. First person:
Hold a container with a capacity of at least 0.6 litres below
the oil drain plug.
Second person:
Tilt the machine to allow the oil to flow out.
3. Thoroughly clean the area around the oil outlet.
4. Retighten the oil drain plug.
5. Remove the oil filling plug (33).
6. Slowly pour 0.6 litres of new oil (for oil type see
"Fuelling") into the hole.
7. Tighten the oil filling plug (33).
8. Wipe off oil residues/spilling.
33

Publicité

Table des Matières
loading

Table des Matières