MINN KOTA RIPTIDE ULTERRA Guide De Démarrage Rapide page 4

DEPLOYING THE MOTOR
1. Double press the stow/deploy button on the remote.
2. The stow/deploy icon will flash on the remote LCD until motor is
fully deployed.
TRIMMING THE MOTOR
1. With the motor deployed, press the trim up/down button on the
remote to trim motor in the desired direction.
STOWING THE MOTOR
1. Press the stow/deploy button on the remote.
2. The stow/deploy icon will flash on the remote LCD until motor is
fully stowed.
ENGAGING SPOT-LOCK
1. Press the Spot-Lock button on the remote.
2. The Memory Location icon will flash on the remote LCD for three
seconds, allowing you to choose a memory location by pressing
the Speed Up or Speed Down buttons. Pressing the Spot-Lock
button again or waiting for three seconds accepts the memory
location.
DISENGAGING SPOT-LOCK
1. To disengage Spot-Lock press any of these buttons: Prop On/
Off, Steer Right, Steer Left, Speed Up, Speed Down or Spot-
Lock.
RE-ENGAGE A SAVED SPOT-LOCK LOCATION
1. Manually navigate the boat to within a quarter mile of the saved
Spot-Lock location. Due to safety reasons, i-Pilot will not re-
engage a saved Spot-Lock location greater than a quarter mile
away.
2 Press the Spot-Lock Recall button on the remote.
3. The Memory Location icon will flash on the remote LCD for three
seconds allowing you to choose a memory location by pressing
the Speed Up or Speed Down buttons. Pressing the Spot-Lock
Recall button again or waiting for three seconds accepts the
memory location.
SPOT-LOCK ESCAPE
1. If the Spot-Lock button is accidentally hit, press the Record
Pause/Escape button or any manual navigation button within
three seconds to cancel the command.
ENGAGING CRUISE CONTROL
1. Press the Cruise Control button on the remote.
2. The current GPS speed will flash, displaying your current speed
as the target GPS speed on the remote LCD for three seconds.
3. Press the Speed Up or Speed Down buttons to increase or
decrease the target speed or press the Cruise Control button
again to engage Cruise Control immediately.
DISENGAGE CRUISE CONTROL
1. Pressing the Cruise Control button will disengage Cruise Control.
ADJUSTING TARGET SPEED
WITH CRUISE CONTROL ENGAGED
1. With Cruise Control engaged press the Speed Up or Speed
Down buttons to adjust the target speed by 0.1 MPH
increments.
ENGAGING ADVANCED AUTOPILOT AND AUTOPILOT
1. To engage Advanced AutoPilot, press the AutoPilot button
once. To engage AutoPilot, press and hold the AutoPilot button
for two seconds.
2. The Advanced AutoPilot or AutoPilot icon will be displayed on
the remote LCD.
3. To adjust desired heading, manually steer motor to new heading.
i-Pilot will lock onto new heading.
RECORDING A TRACK
1. Press the Record button on the remote.
2. The Memory Location icon will flash on the remote LCD for three
seconds, allowing you to choose a memory location by pressing
the Speed Up or
Speed Down buttons. Pressing the Record button again or
waiting for three seconds accepts the memory location.
3. The REC icon will be displayed on the remote LCD. Remember
this will be the start point on the track.
4. Navigate the boat along the desired path or course. AutoPilot
and/or Cruise Control can be used while recording a track.
5. Press the Record button on the remote again to stop the
recording. The recording will end automatically if the two-mile
distance limit is reached for the track or if one of the following
buttons are pressed: Spot-Lock, Spot-Lock Recall, Track to End
or Track to Start.
PAUSE AND RESUME A RECORDING
1. While recording a track press the Record Pause/Escape button.
2. The record icon will flash on the remote LCD.
3. i-Pilot has now paused the recording of the track.
4. If the boat moves farther than a quarter mile from where the
Record Pause/Escape button was pressed, the recorded track
will be ended and saved to the memory location previously
selected.
5. When ready to resume recording, navigate the boat just ahead
of where the Record Pause/Escape button was pushed. Failure
to do this may cause erratic play back of a track.
6. Push the Record Pause/Escape button.
7. The record icon will stop flashing on the remote LCD.
8. i-Pilot is now recording again and adding to the
track that was paused.
REPLAYING A TRACK
(TRACK TO START / TRACK TO END)
1. Manually navigate the boat to within a quarter mile of the saved
track. Due to safety reasons, i-Pilot will not re-engage a saved
track greater than a quarter mile away.
2. Press the Track to Start or Track to End button on the remote.
3. The Memory Location icon will flash on the remote LCD for three
seconds, allowing you to choose a memory location by pressing
the Speed Up or Speed Down button. Pressing the button
pressed in step 2 again or waiting for three seconds accepts
the memory location.
4. Adjust motor speed to desired setting to engage and navigate
track automatically.
RECORD, TRACK TO END AND
TRACK TO START/ESCAPE
1. If the Record, Track to Start or Track to End button is
accidentally hit, press Record Pause/Escape button within three
seconds on the remote to cancel the command.
2207102ra