Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
FR
EN DE
ES
EN
FR
DE
ES
DE
FR
EN
ES
ES
FR
EN
DE
Replace the clutch cover and rotate clutch cover lock
■
IT
FR
EN
DE
ES
knob just enough to hold the cover in position.
Replace the clutch cover and tighten up the nut
FR
EN
DE
ES
IT
just enough to hold the clutch cover in place. (For
HCS3335B only)
FR
EN
DE
ES
IT
NOTE: The bar must be free to move for tension
adjustment.
FR
EN
DE
ES
IT
Remove all slack from the chain by rotating the chain
■
tensioning dial clockwise until the chain seats snugly
FR
EN
DE
ES
IT
against the bar with the drive links in the bar groove.
Lift the tip of the guide bar up to check for sag.
FR
EN
DE
ES
IT
■
Release the tip of the guide bar and turn the chain
■
FR
EN
DE
ES
IT
tensioning dial clockwise. Repeat this process until
sag does not exist.
FR
EN
DE
ES
IT
Hold the tip of the guide bar up and tighten the
■
clutch cover lock knob securely. The chain is correctly
FR
EN
DE
ES
IT
tensioned when there is no sag on the underside of
the guide bar, the chain is snug, but it can be turned
FR
EN
DE
ES
IT
by hand without binding. Ensure that the chain brake
is not set.
FR
EN
DE
ES
IT
Hold the tip of the guide bar up and tighten the clutch
cover nut securely. (For HCS3335B only)
FR
EN
DE
ES
IT
Note: If chain is too tight, it will not rotate. Loosen
the clutch cover lock knob by pressing in and slightly
FR
EN
DE
ES
IT
rotating counter clockwise, then rotate the chain
tensioning dial counter clockwise. Lift the tip of the
FR
EN
DE
ES
IT
guide bar up and retighten the clutch cover lock knob
securely. Ensure that the chain will rotate without
FR
EN
DE
ES
IT
binding.
FR
EN
DE
ES
IT
chAIN MAINTENANcE
FR
EN
DE
ES
IT
See Figures 45 - 47.
FR
EN
DE
ES
IT
WARNINg:
Check that the switch is in the STOP "0" position
FR
EN
DE
ES
IT
before you work on the saw.
Use only a low-kickback chain on this saw. This fast-
cutting chain provides kickback reduction when properly
maintained.
For smooth and fast cutting, maintain the chain properly.
The chain requires sharpening when the wood chips are
small and powdery, the chain must be forced through the
wood during cutting, or the chain cuts to one side. During
maintenance of the chain, consider the following:
Improper filing angle of the side plate can increase
■
the risk of severe kickback.
Raker (depth gauge) clearance.
■
- Too low increases the potential for kickback.
- Not low enough decreases cutting ability.
If the cutter teeth hit hard objects such as nails and
■
stones, or are abraded by mud or sand on the wood,
have an authorised service centre sharpen the chain.
Note: Inspect the drive sprocket for wear or damage
when replacing the chain. If signs of wear or damage are
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
NL
PT
SV
DA NO
SV
PT
NL
DA NO
DA
PT
NL
SV
NO
PT
NL
SV
DA
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
English
FI
HU CS RU
present in the areas indicated, have the drive sprocket
FI
HU CS RU
replaced by an authorised service centre.
NOTE: If you do not fully understand the correct
FI
HU CS RU
procedure for sharpening the chain after reading the
instructions that follow, have the saw chain sharpened
FI
HU CS RU
by an authorised service centre or replace with a
recommended low-kickback chain.
FI
HU CS RU
SHARPENINg THE CUTTERS
NO
FI
HU CS RU
See Figures 48 - 51.
Be careful to file all cutters to the specified angles and
FI
HU CS RU
to the same length, as fast cutting can only be obtained
when all cutters are uniform.
FI
HU CS RU
WARNINg:
HU
FI
CS RU
The saw chain is very sharp. Always wear
protective gloves when performing maintenance
CS
FI
HU
RU
to the chain to prevent serious personal injury.
RU
FI
HU CS
Tension the chain prior to sharpening. Refer to
■
Adjusting The chain Tension.
FI
HU CS
RU
Use a 5/32 in. (4 mm) diameter round file and holder.
■
Do all of your filing at the midpoint of the bar.
FI
HU CS
RU RO
Keep the file level with the top plate of the tooth. Do
■
FI
HU CS
RU RO
not let the file dip or rock.
Using light but firm pressure. Stroke towards the front
■
FI
HU CS
RU RO
corner of the tooth.
Lift the file away from the chain tooth on each return
FI
HU CS
■
RU RO
stroke.
Put a few firm strokes on every tooth. File all left
FI
HU CS
RU RO
■
hand cutters in one direction. Then move to the other
side and file the right hand cutters in the opposite
FI
HU CS
RU RO
direction.
FI
HU CS
RU RO
Remove filings from the file with a wire brush.
■
CAUTION:
FI
HU CS
RU RO
A dull or improperly sharpened chain can cause
excessive engine speed during cutting, which may result
in severe engine damage.
WARNINg:
Improper chain sharpening increases the
potential of kickback.
WARNINg:
Failure to replace or repair a damaged chain can
cause serious injury.
TOP PLATE FILINg ANgLE
See Figure 52.
CORRECT 30° – file holders are marked with guide
■
marks to align file properly to produce correct top
plate angle.
LESS THAN 30° – for cross cutting.
■
MORE THAN 30° – feathered edge dulls quickly.
■
42
RO PL
SL
HR ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO
PL
SL
HR
ET
PL
SL
HR
ET
SL
PL
HR
ET
HR
PL
SL
ET
ET
PL
SL
HR
PL
SL
HR
ET
PL
SL
HR
ET
PL
SL
HR
ET
PL
SL
HR
ET
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LV
LT
SK BG
SK
LT
LV
BG
BG
LT
LV
SK
Publicité
Table des Matières
