Overview Of Master Commands - Balluff BOD 26K LB04-S115-C Instructions De Service Et De Montage

8.4

Overview of master commands:

Command description Dec.
Set switching output Q
Set switching output Q
Set Q as output
2
„Good Target"
Set Q as Trigger input
1
Set Q as control input
1
for laser ON/OFF
Averaging
Scaling analogue
output (4 mA)
Scaling analogue
output (20 mA)
„Autom. zero" function
(with Q as control
1
input)
Autom. centre" (with Q
as control input)
„Maximum Hold" func-
tion (with Q as control
1
input)
Minimum Hold" function
(with Q as control
1
input)
„Difference Hold" func-
tion (with Q as control
1
input)
Activate factory setting
64
Hex.: ASCII Remark
49 31 1
1
50 32
2
2
71 47 G
84 54 T
69 45 E
66 42
B
78 4E
N
72 48
H
90 5A Z
67 43
C
1
88 58
X
77 4D M
68 44 D
87 57 W
Switching output Q is set:
1
1st and 2nd switching point
N.C / N.O.
Pulse stretching
Switching output Q is set:
2
1st and 2nd switching point
N.C / N.O.
Pulse stretching
Q switches when an object is in the measuring range
2
(Good Target).
Q is set as trigger input. With rising edge on Q
1
measured value is held until the next trigger occurs.
Used to switch laser beam on and off.
Q = +U (laser beam ON),
1 B
Q = -U (laser beam OFF).
1 B
Last measured value remains. When reactivated, the
response time is prolonged according to the set mean
value.
The number of meas. values used for averaging
(arithmetic mean) is set (1 / 10 / 100 meas. values).
The transmitted value is set as 4 mA point at analo-
gue output.
The transmitted value is set as 20 mA point at analo-
gue output.
The output characteristics 4 ... 20 mA are displaced.
If Q = +U the current measured value is set as the
1 B
analogue value 4 mA. The incline of the characteri-
stics is maintained. The max. value of the characteri-
stics is limited by the measuring range.
The output characteristics 4 ... 20 mA are displaced.
If Q = +U the current measured value is set as the
1 B
analogue value 12 mA. The incline of the characte-
ristics is maintained. The min. or max. value of the
characteristics are limited by the measuring range.
Provided Q = +U , the max. recorded measured
1 B
value is stored. If Q = -U
1
transmitted at the analogue output or can be called up
via „Measured operating values".
Provided Q = +U , the min. recorded measured
1 B
value is stored. If Q = -U
1
transmitted at the analogue output or can be called up
via „Measured operating values".
Provided Q = +UB, the difference between the mea-
1
sured values is saved. If Q
value is transmitted at the analogue output or can be
called up via „Measured operating values".
The sensor resets all settings to the factory setting
incl. sensor address.
No. 834826 E Edition 1310; Replaces edition 1111; Subject to modification
Mounting and
operating instructions
,
1
, the determined value is
B
, the determined value is
B
= -U , the determined
1 B
Example
8.5.1
8.5.2
8.5.3
8.5.4
8.5.5
8.5.6
8.5.7
8.5.8
8.5.9
8.5.10
8.5.11
8.5.12
8.5.13
8.5.14