Installation; Side Panels; Side Cleats - Monogram ZIC360NHLH Instructions D'installation

INSTALLATION

ZUG2 Unified Grille Panel Kit
• If you are installing two units, side by side, the
installation space must be 75" (190.5 cm) wide.
Note: Additional cutout width may be required when
side panels are used. Add side panel thickness to the
finished cutout to calculate rough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
NOTE: When implementing a dual installation, the
factory installed standard case trim should be used on
the handle side of each unit and the supplied flush case
trim should be used on the hinge side of each unit.
75" Finished Width
4-5/16"
Electrical
5-1/2"
9"
24" Minimum
Cutout Depth
Cold Water
Supply
85" Max
Finished
Opening
3-1/2" 3-1/2"
7"
3-1/2"
3-1/2"
ZUG2 GRILLE PANEL DIMENSIONS
The ZUG2 unified grille panel kit provides for the
installation of a framed or overlay grille panel.
Framed Panel Dimensions
A (Width)
3/4" (1.91 cm)
Routed Panel 74" (187.96 cm)
Overlay Panel Dimensions
A (Width)
1/4" (0.63 cm)
Backer Panel 69-7/8" (177.48 cm)
0.10" (0.25 cm) 68-1/2" (173.99 cm)
Spacer Panel
1/2" (1.27 cm) 74" (187396 cm)
Smooth Panel
31-49142 Rev. 2
Design Guide - Flush Installation
Wall View
24-3/16"
5-1/2"
Electrical
9"
Area
75-1/2" From
Cold Water
Floor to Bottom
Supply
of Electrical Area
3-1/2" 3-1/2"
7-1/2" 7-1/2" 7"
3-1/2"
3-1/2" 3-1/2" 3-1/2"
B (Height)
10-11/16" (27.15 cm)
B (Height)
8-7/8" (22.54 cm)
7-5/8" (19.37 cm)
10-11/16" (27.15 cm)
Assemble the
overlay panels
in the same
manner as
the door and
drawer panels.

SIDE PANELS

Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The 1/4" (0.63 cm) side
panels will slip into the
side case trim. Secure the
panels to the refrigerator
with stick-on hook and loop
fastener strips. Order the
side panels from the cabinet
manufacturer.
• Cut a notch in the top front
corner as shown to allow
clearance for corner keys
in the front side trim.
* Depending on installation height.

SIDE CLEATS

Wood cleats are required to be installed vertically down
both sides of the cabinet opening to provide depth stop
for the refrigerator when installed into the opening.
The cleat should be installed per the diagrams below
based on the type of panel being used.
Finished
Cleat
5-1/4"
Finished
Cleat
5-3/8"
UNIFIED DOOR PANEL DIMENSIONS
Door panel dimensions for dual installation are:
FF Door: 46-9/16" (125.89 cm) x 36-7/8" (93.66 cm)
FZ Drawer: 22-7/16" (56.99 cm) x 36-7/8" (93.66 cm)
29
24"
*84"
*3" to 4"
2-9/16"
TOP VIEW
DOOR
1/2"
3/4" Panel
Case Trim
TOP VIEW
DOOR
1/2"
1/2" Panel
Case Trim
3/16"
1-7/8"