Assembly Components; Steering Wheel Assembly; Seat Assembly; Mounting The Rear Bumper - Stiga MPST 84 Li 48 V1 Manuel D'utilisation

5.1 ASSEMBLY COMPONENTS

The packaging holds the components needed
for assembly as listed in the table below:
Description
1 Steering wheel
2 Dashboard cover and steering
wheel assembly parts
3 Driving seat
4 Battery charger
5 Front bumper
6 Anti-scalping wheels
7 Grass catcher with relative mounting
screws and relative instructions (only
for models with rear grass catcher)
8 Lower part of the rear plate, the grass
catcher bag supports and relative at-
tachment and fitting accessories (only
for models with rear grass catcher)
9 Side discharge chute (for models with
side discharge only)
10 Side reinforcements of the cutting
means assembly (for models with
side discharge only, if available)
11 Envelope containing:
- the instruction manuals and documents
- driving seat assembly screws
- side discharge chute assembly fittings
(for models with side discharge only)
- 2 starter keys
12 Mobile phone holder kit (if provided)
5.1.1 Unpacking
1. Carefully open the packaging, paying
attention not to lose components.
2. Consult the documentation in the
box, including these instructions.
3. Remove all the unassembled
parts from the box.
4. Remove the machine from the packaging
taking the following precautions:
• move the cutting means assembly
to its maximum height (par. 6.4) to
protect it against damage when the
machine is lifted off the base pallet;
• Move the front drive release lever to
the released position (par. 6.3);
• Lift the machine off the base pallet.

5.2 STEERING WHEEL ASSEMBLY

1. Put the machine on a flat surface
and straighten the front wheels.
2. Fit the hub (fig. 3.A) on the steering shaft
(fig. 3.B) making sure that the pin (fig. 3.C)
is correctly inserted into its seat in the hub.
3. Replace the cap on the dashboard
(fig. 3.B) inserting the five fittings
so they click into place.
4. Fit the steering wheel (fig. 3.E) on the
hub (fig. 3.A) with the spokes pointing
towards the seat.
5a. Only for steering wheel of type "I"
- Insert the spacer (fig. 3.F) and fix the
steering wheel using the supplied screws
(fig. 3.G) in the indicated sequence.
5b. Only for steering wheel of type "II" - Fix
the steering wheel using the supplied screws
(fig. 3.F, 3.G) in the indicated sequence.
6a. Only for steering wheel of type "I" -
Apply the steering wheel cover (fig. 3.H)
inserting with a click into its seat.
6b. Only for steering wheel of type "II" -
Apply the mobile phone cover (fig. 3.H)
inserting with a click into its seat.

5.3 SEAT ASSEMBLY

Fit the seat (fig. 4.A) on the plate (fig. 4.B) using
the screws (fig. 4.C).

5.4 MOUNTING THE REAR BUMPER

1a. Only for bumper of type "I" - Fit
the front bumper (fig. 5.A) on the
lower part of the frame (fig. 5.B)
using the four screws (fig. 5.C).
1b. Only for bumper of type "II"
1. Fit the two supports (fig. 5.A) and
(fig. 5.B) on the lower part of the frame
(fig 5.C) observing the fitting order
indicated in the figure R= right; L= left.
2. Fully tighten the screws (Fig. 5.D).
3. Fix the front bumper (fig. 5.E) to the
supports (fig. 5.A) and (fig. 5.B) using
the screws (fig. 5.F) and nuts (fig. 5.G).
5.5 SIDE DISCHARGE CHUTE
ASSEMBLY (FOR MODELS WITH
SIDE DISCHARGE ONLY)
1. From the inside of the side discharge
chute (fig. 6.A), fit the spring (fig. 6.B) by
inserting the terminal (fig. 6.B.1) into the
EN - 10