Insuring Your Lawnmower; Assembly; Assembly Components (3); Seat - Stiga Park 4WD Serie Manuel D'utilisation

(Translation of the Original Instructions)
• When the machine is withdrawn from service,
do not dump it in the environment, but take it to
a waste disposal facility in accordance with the
local regulations in force.

4 INSURING YOUR LAWNMOWER

Check the insurance on your lawnmower.
Contact your insurance company.
You ought to have fully comprehensive insurance
for traffic, fire, damage and theft.

5 ASSEMBLY

Do not use the machine until all the in-
dications provided in the "ASSEMBLY"
section have been carried out .
Unpacking and completing the as-
sembly should be done on a flat and
stable surface, with enough space for
machine handling and its packaging,
always making use of suitable equip-
ment .
5 .1

ASSEMBLY COMPONENTS (3)

The machine is delivered with the seat, armrests,
steering wheel, tow bar, quick-fit supports disman-
tled. The battery is in its housing and connected.
The packaging holds the components needed for
assembly (3) as listed in the table below:
[740 IOX; 540 IX]
Pos. No. Description
A 2 Spring pin
B 2 Key for switch
C 1 Key for main power switch
D 2 Armrests
E 4 Screws for seat fastening
F 10 Pegs for bellows fastening
G 4 Bushes for seat fastening
H 4 Split lock washer
L 4 Hex head screw
M 1 Carrier
N 4 TORX screws (carrier
fastening)
O 1 Tow bar
P 2 Flanged nut
R 2 Quick-release supports
ENGLISH
Pos.
A
B
C
D
M
N
O
P
Q
R
S
5 .2

5 .2 .1 Armrest assembly (6)

You will find the armrests and the components for
their installation in a separate box in the machine
packaging.
5 .2 .2 Seat assembly (5) (Mod . 740 IOX, 540
1. Smear oil over the 4 sliding runners (5:A).
2. Prepare the 4 screws (M8 x 40) by inserting
3. Lift the seat support (5:C) to an upright po-
4. Bring the seat towards the support and insert
Dimensions
6 x 36
/
5. Make sure the seat is right up against the
/
/
M8 x 40
6. Insert and tighten the 4 screws (5:B).
7. Fasten the screws, tightening torque 20÷25
M8
M8 x 20
8. Connect the seat connector (5:E) to the wiring
M6 x 20
M8
9. Pass the wiring cable in the fastening clip
[340 IX]
No. Description
2 Spring pin
2 Key for switch
1 Key for main power switch
2 Armrests
1 Carrier
4 TORX screws (carrier fastening)
1 Tow bar
2 Flanged nut
2 Hex head screw
2 Quick-release supports
2 Seat fastening pin

SEAT

Install the seat following the instruc-
tions in the following order .
IX)
them in the spring lock washers and bushes.
See (5:B).
sition.
the assembly (5:B) in the slot (5:D) on the
support.
support and position it so that the holes for
the fixing screws are about halfway along the
sliding runners.
Nm.
Tightening the screws to a torque over
25 Nm, will damaged the seat .
connector (5:F).
If the connectors are not connected the
machine will not work .
(5:H) to hold it in position.
EN
Dimensions
6 x 36
/
/
/
M6 x 20
M8
M8 x 20
M8
11