Maintenance And Storage; Description Of Components - Sabo 45-220 Livret D'entretien

The equipment must not be operated with damaged covers or without
correctly attached covers.
– Exhaust protection grill (
The engine/exhaust becomes very hot. The protection grill protects
the user against burns.
Do not operate the machine without the exhaust protection grill.
The safety devices must not be modified.
• Do not change the basic settings of the engine or operate the engine at
excessive speed.
When you start the machine, make sure that your feet are at a sufficiently
safe distance away from the cutting blades.
When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the
cutting tool is pointing in the direction away from the user, but only as far
as absolutely necessary. As long as the equipment has not been lowered
to the ground again, both your hands must be on the top part of the bar.
Never put your hands or feet near or under revolving parts. Always make
sure that your hands or feet do not get under the housing.
Stop the engine by releasing the motor stop bar, disconnect the spark-
plug connector, make sure that all moving parts have come to a complete
standstill and the ignition key, if there is one, has been removed:
– if you intend to leave the machine;
– before you inspect, clean or carry out work on the machine;
– before unblocking jams or removing blockages in the ejection
channel;
– if a foreign body has been encountered.
– when the machine starts to vibrate strangely.
• If a foreign object has been encountered or if the machine becomes
blocked, e.g. by driving onto an obstacle, a specialist dealer must check whether
parts of the machine have been damaged or deformed. Any necessary repairs
must also be carried out by an authorized specialist workshop.
• If the machine starts to vibrate unusually heavily or to make unusual noises,
please have it checked immediately by an authorised workshop.
Heavy vibrations on your hands can damage your health. Please contact an
authorised workshop immediately if heavy vibrations occur.
• WARNING
The noise and vibration levels shown in these operating instructions are the
maximum levels for use of the machine.
The use of an unbalanced cutting element, the excessive speed of movement, or
the absence of maintenance have a significant influence on noise emissions and
vibrations. Consequently, it is necessary to take preventive steps to eliminate
possible damage due to high levels of noise and stress from vibration.
Maintain the machine well, wear ear protection devices, and take breaks while
working.
Adhere to the maintenance work listed in this operating manual and have the
equipment checked and serviced regularly by an authorised workshop.
Stop the engine by releasing the motor stop bar, make sure that all moving
parts have come to a complete standstill,
– when you have to lift or tilt the scarifier e.g. for transportation;
– when you need to transport the machine to and from the area to be
scarified;
– when driving off the lawn;
– if you have to leave the machine for a short time;
– if you wish to adjust the scarifying depth;
– before you fill it with fuel. Only refill when the engine is cold!
• If the engine is equipped with a petrol shut-off valve, this should be closed
after scarifying.

Maintenance and storage

• Insufficient equipment maintenance will lead to safety-related faults.
• Ensure that all screws have been tightened securely and that the machine
is in a safe working condition.
Never store a machine which still contains petrol inside a building where
petrol fumes may come into contact with naked flames or sparks or where
they may ignite.
The engine and exhaust reach very high temperatures during operation.
)
11
Allow the machine to cool down for at least 15 minutes before starting any
maintenance or cleaning work.
• To avoid a fire hazard, keep the engine, muffler (exhaust) and fuel tank free of
grass, leaves or escaping oil (grease).
When tilting the machine upwards or placing it on its side, make sure no oil or
petrol escapes. Fire hazard!
Allow the engine to cool down before you store the machine in closed rooms.
Do not store the machine near open flames or sources of fire such as boilers or
heating systems.
Before you start scarifying, always check the condition and firm attachment
of the cutter blade shaft. Worn or damaged blades must always be replaced.
Always have a specialist workshop replace the cutter blades or work on the
cutter blade shaft. If the cutter blade shaft is assembled incorrectly parts can
become loose, which can lead to serious injuries.
• For reasons of safety, always replace worn or damaged parts.
Protective gloves must be worn at all times during maintenance and
cleaning work.
• When handling operating fluids, such as engine oil and fuel, suitable protective
equipment (e.g. suitable protective gloves) must be worn.
The data sheets of the operating fluids must be observed.
Maintenance and cleaning work may only be carried out on level surfaces
with the engine switched off and the spark plug connector disconnected.
Regular maintenance is essential for safety and top performance.
• Never remove the spark plug connector when the motor is running! Risk: Electric
shock.
• Disconnect the spark plug connector only when the engine has cooled down.
Danger of burns!
• Make sure that the spark plug connector is firmly seated! Risk: Electric shock.
• If the tank has to be emptied, this should be done in the open, and with a
cold engine. Take care to ensure that no fuel is spilt.
• Only store the scarifier with the cutter raised. A lowered cutter may bend over time
and compromise the operational safety of the scarifier.
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.

7 DESCRIPTION OF COMPONENTS

1 Safety grip
2 Tank cap
3 Belt drive cover
4 Oil filling nozzle
5 Engine fixing
6 Adjusting screw scarifying depth
7 Splash guard
8 Engine cover
9 Petrol tap
10 Air filter
11 Exhaust protection grill
12 Spark plug
5