Pc1616/1832/1864 Programming - DSC TL260GS Manuel D'installation

TL260GS/GS2060 Communicator Wiring Diagram
WARNING! All connections to the
TL260GS/GS2060 module are power
limited. Do not route any wiring over the
circuit boards. Maintain at least 1"
(25.4mm) separation between circuit
board and wiring. A minimum of 1/4"
(7mm) separation must be maintained at
all points between non-power limited
wiring and power limited wiring.
NOTE: For more details, refer to the
control, panel Installation Manual p/n
29007359.
AUX+ BELL+
AC AC
AUX-
Wiring TL260GS/GS2 060 to PC1616/1832/1864 Control Panel
• Remove the circular knock out in the top right-hand corner of the cabinet and mount the TL260GS/GS2060 module in place (secure
using screws supplied).
• Attach the TL260GS/GS2060 antenna to the unit.
• With both the AC and battery disconnected from the DSC control panel, wire the supplied PC-Link cable.
• Wire the Bell+ of the control panel to the TL260GS/GS2060 PWR terminal.
• Wire the AUX- on the control panel to the TL260GS/GS2060 GND.
• Connect the PC-Link Cable
• Insert the connector on the TL260GS/GS2060 with the black wire on Pin 1 of the PC-Link header.
• Insert the other end of the cable on the PC1616/1832/1864 with the red wire on Pin 1 of the PC-Link header.
• Apply AC and DC to the main control panel, the TL260GS/GS2060 and the PC1616/1832/1864 should power up.
• Perform the necessary programming.
NOTE: If a Bell/Siren is not being used, wire the Bell/Siren terminals on the panel with a 1K ohm resistor, then only wire the BELL+ to the
PWR of the TL260GS/GS2060.
Optional Antenna Kits
The TL260GS/GS2060 comes with a standard external GSM radio antenna. If the required GSM signal strength cannot be achieved
using this antenna, the following selection of GSM extension antenna kits are available to the installer:
• GS15-ANTQ - 4.57m (15') Internal Antenna Extension Kit suitable for interior mounting only
• GS25-ANTQ - 7.62m (25') External Antenna Extension Kit suitable for exterior mounting only
• GS50-ANTQ - 15.24m (50') External Antenna Extension Kit suitable for exterior mounting only
Specific instructions for the installation of each extension antenna are included with each kit.

PC1616/1832/1864 Programming

In order that your Communicator and your panel operate correctly together, specific panel options must be set. Take the following steps
to ensure that your Communicator and your panel work together as intended.
These options must be set at the panel keypad.
1. Program the hexadecimal digits (DCAA) in the telephone number that will be used for the GPRS/Ethernet Communicator (panel sec-
tions [301], [302], [303], 'Telephone Phone Number Programming').
Panel sections [301], [302], [303]
• If a legitimate telephone number is entered in these options, signal will be communicated using PSTN. If DCAA is entered, signals
will be routed depending on the GS/IP module programming.
• Panel section [301] is Primary communication path, and may be configured either as PSTN or DCAA. Panel section [302] is redun-
dant, and panel section [303] is the backup telephone number to section [301].
NOTE: The leading digit 'D' in the telephone number for dial tone detection is pre-programmed.
2. In panel section [350], program the communication format as SIA FSK. If any of the panel telephone numbers have been set to DCAA,
panel section [350] must be set to SIA.
3. In panel sections [351] through [376], program the call direction options for the phone number being used to communicate using the
GPRS/Ethernet Communicator.
4. Panel section [382], option [5], 'T-Link Interface Enabled' must be set to ON. If this option is OFF, the status LED will indicate the
'Panel Supervision Trouble' and the unit could not be programmed via PC-Link cable.
5. Panel section [167]: Set the value to 60 seconds.
6. Panel section [401]: Option [1] must be set to ON in order to perform panel DLS session through GPRS or Ethernet.
PC1616/1832/1864
UA503
PGM1 PGM3
RED BLK YEL GRN Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8
BELL-
PGM2 PGM4
To external
antenna
Radio
SIM Card
Holder
PWR PWR GND GND
PC-LINK
1
1 CON 4
PC-LINK
See PC-Link wiring
instructions below
RING R-1
EGND
TIP T-1
5
TL260GS / GS2060
GND SHLD
Network Connection
(Available only for model
TL260GS) Use only CAT5
cable (300ft/100m max.)
Supervised
Input Ratings (from Bell Out)
11.1V - 12.6 V
DC
100mA standby
400mA Alarm
DSC Panel minimum
power requirements
16 V 40 VA transformer
AC
12 V 7Ah battery
DC
+
-