gefran SIEIDrive LIFT AGy-L Mode D'emploi page 230

LCD Display
I.210 An in 2 Type Setting of the Analog Input 2 type reference (voltage)
I.211 An in 2 offset Analog Input 2 offset
I.212 An in 2 gain Analog Input 2 gain
I.213 An in 2 minimum An Input 2 minimun value
I.214 An in 2 filter Time constant of digital filter on Analog input 2
I.215 An in 2 DeadBand Analog Input 2 dead band
I.220 An in 3 Type Setting of the Analog Input 3 type reference (current)
I.221 An in 3 offset Analog Input 3 offset
I.222 An in 3 gain Analog Input 3 gain
I.223 An in 3 minimum An Input 3 minimun value
I.224 An in 3 filter Time constant of digital filter on Analog input 3
I.225 An in 3 DeadBand Analog Input 3 dead band
I.300 Analog out 1 cfg Analog Output 1 configuration
I.301 An out 1 offset Analog output 1 offset
I.302 An out 1 gain Analog output 1 gain
I.303 An out 1 filter Time constant of output filter
I.310 Analog out 2 cfg Analog Output 2 configuration
I.311 An out 2 offset Analog output 2 offset
I.312 An out 2 gain Analog output 2 gain
I.313 An out 2 filter Time constant of output filter
I.350 Exp an out 1 cfg Expansion Analog Output 1 configuration (on Exp. board)
I.351 Exp AnOut 1 offs Expansion Analog Output 1 offset
I.352 Exp AnOut 1 gain Expansion Analog Output 1 gain
I.353 Exp AnOut 1 filt Time constant of output filter
I.400 Inp by serial en Virtual Digital enabling
I.410 Exp in by ser en Expansion Virtual Digital
Inputs enabling
I.420 Out by serial en Virtual Digital Outputs setting enabling
I.430 Exp OutBySer en Expansion Virtual Digital Outputs enabling
I.450 An out by ser en Virtual Analog Outputs enabling
I.500 Encoder enable Enabling of the encoder measure
I.501 Encoder ppr Encoder nameplate pulses per revolution
230
PARAMETER
DESCRIPTION
PICK LIST
LCD Selection Description
[0] +/- 10V
[1] 0-10V/0-20mA
[1] 0-10V/0-20mA Bipolar ± 10V
Unipolar +10V
[2] 4-20mA
[0] Freq out abs Output Frequency absolute
value.
[1] Freq out Output Frequency.
[2] Output curr Output Current.
[3] Out voltage Output Voltage.
[4] Out trq (pos) Output Torque positive value.
[5] Out trq (abs) Output Torque absolute value.
[6] Out trq Output Torque.
[7] Out pwr (pos) Output Power positive value.
[8] Out pwr (abs) Output Power absolute value.
[9] Out pwr Output Power.
[10] Out PF Output Power Factor.
[11] Enc freq abs Encoder frequency absolute
value.
[12] Encoder freq Encoder frequency.
[13] Freq ref abs Frequency reference absolute
value.
[14] Freq ref Frequency reference
[15] Load current Load Current.
[16] Magn current Motor Magnetizing Current.
[17] PID output PID regulator output.
[18] DClink volt DC bus capacitors level.
[19] U current Output phase U current signal.
[20] V current Output phase V current signal.
[21] W current Output phase W current signal.
[22] Freq ref fac Multiplier factor for frequency
reference
As for I.300
As for I.300
[0] Disable Encoder measure disabled.
[1] Enable Encoder measure enabled.
0 0 1
0 -99.9 99.9 % 0.1
1 -9.99 9.99 % 0.01
0 0 99.99 % 0.01
0.1 0.001 0.25 sec 0.001
0 0 99.9 % 0.1
1 1 2
0 -99.9 99.9 % 0.1
1 -9.99 9.99 % 0.01
0 0 99.99 % 0.01
0.1 0.001 0.25 sec 0.001
0 0 99.9 % 0.1
0 0 22
0 -9.99 9.99 0.01
1 -9.99 9.99 0.01
0 0 2.5 sec 0.01
2 0 22
0 -9.99 9.99 0.01
1 -9.99 9.99 0.01
0 0 2.5 sec 0.01
3 0 22
0 -9.99 9.99 0.01
1 -9.99 9.99 0.01
0 0 2.5 sec 0.01
0 0 255
0 0 15
0 0 15
0 0 3
0 0 255
0 0 1
1024 1 9999
AGy -L
IPA
123
124
125
126
127
183
128
129
130
131
132
184
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151