Notes On The Documentation; Use In Compliance With The Documentation; Basic Safety Rules; Product Identification - AERMEC ANR Série Notice D'installation Et De Maintenance

1. 1 Use in compliance with the do-
cumentation
AERMEC heat pumps are constructed
according to the recognised technical
standards and safety regulations. These
appliances are designed and built for hea-
ting and hot water production for sanitary
applications and must be used in compa-
tibility with their technical features. Howe-
ver, dangers to the user or third parties
may arise, as well as damage to the ap-
pliance and other objects, in the event of
improper use not in compliance with the
type of use envisaged.
Any use not expressly indicated in this
manual is not permitted. Consequently
AERMEC will not assume any respon-
sibility for damage that may occur due
We remind you that the use of products
that employ electrical energy and water
requires that a number of essential sa-
fety rules be followed, including:
This appliance is not suitable for use
by persons (including children) with li-
mited physical, sensory, or mental ca-
pacities or those lacking experience
or knowledge, unless they are super-
vised or instructed regarding the use
of the appliance by a person who is
responsible for their safety. Children
must always be supervised to ensure
they do not play with the appliance.
It is prohibited to carry out any techni-
The ANR heat pump can be identified
by means of:
- Packing label
which shows the product identifica-
tion data
- Technical plate
Positioned on the fixed panel in the
lower part in the area of the lateral
hydraulic and electrical connections
NOTE
Tampering, removal, or lack of the iden-
tification plate or other does not permit
sure identification of the product, and
therefore makes any installation or
maintenance operation difficult
1

NOTES ON THE DOCUMENTATION

to failure to comply with these instruc-
tions.
1.2 Conserving the documenta-
tion
The installation instructions along with all
the related documentation must be given
to the user of the system, who assumes
the responsibility to conserve the instruc-
tions so that they are always at hand in
case of need.
READ THIS DOCUMENT CAREFULLY:
the installation of the appliance must be
carried out by qualified and suitably pre-
pared personnel in compliance with the
national legislation effective in the count-
ry of destination. (Ministerial Decree
329/2004).
2

BASIC SAFETY RULES

cal or maintenance operation before
the unit has been disconnected from
the electrical mains by switching off
the master switch of the system and
the main power switch on the control
panel.
It is prohibited to modify the safety or
adjustment devices without the ma-
nufacturer's authorisation and preci-
se instructions
It is prohibited to jerk, detach, or twist
the electrical cables coming from the
unit even if it is disconnected from
the electrical mains
It is prohibited to leave any contai-
3

PRODUCT IDENTIFICATION

The appliance must be installed in such
a way as to enable maintenance and/or
repairs to be carried out. The appliance
warranty does not cover the costs for lad-
der trucks, scaffolding, or other elevation
systems that may become necessary for
carrying out servicing under warranty.
The validity of the warranty shall be void
in the event of failure to comply with the
above-mentioned indications.
ners or flammable substances in the
vicinity of the heat pump.
It is prohibited to touch the appliance
when you are barefoot and with parts
of the body that are wet or damp.
It is prohibited to open the doors for
accessing the internal parts of the ap-
pliance without first having switched
off the master switch of the system.
It is prohibited to disperse or aban-
don the packing materials, and they
must be kept out of the reach of chil-
dren, as they are a potential source
of danger.
PACKING
LABEL
AE R M E C SP A - via R oma 44
TECHNICAL
37040 - B evilacqua (V R ) - I T AL I A
S R P 14T 00
M OD. vers.
3/N/P E ~400V S R P 00007
50H z Serial no
13.65
P t = kW
C A L DO F R E DDO
3.30
HE A T P e = kW C OL D
PLATE
7.10
C HA UD I n = A F R OI D
46.0
HE I ZUNG K UHL UNG
I s = A
-20 / -20
M in. P S (H P /L P )
T S(H P /L P ) C
130 / 52
M ax. R 407C
R E S.E L /E L .HE AT E R
11.5 I n R x
kW max =
R E S.E L /E -HE I ZUNG I tot
01/2008
P rod. date
24
I P
P f = kW
P e = kW
I n = A
I s = A
28 / 22
bar
5.0
K g
18.3
max = A
31
max = A
37