Night Light Replacement; Pilot Injector And Orifice Replacement - Napoleon Bayfield GDS25N-1 Manuel D'installation

• Access the blower, if equipped and clean using a soft brush and vacuum.
movement is experienced.
• Re-assemble the various components in reverse order.
• Check for gas leaks on all gas connections up and downstream from the gas valve including the pilot tube
• Inspect the relief system. The appliance relieves through the main glass door or through the aps on the
maintenance
connections.
rebox top. Ensure they open freely, and close sealed.
EN
• Check the gas control valve pilot and Hi / Lo knobs move freely (if equipped) – replace if any stiffness in
9.2

night light replacement

10.2 NIGHT LIGHT REPLACEMENT
movement is experienced.
This appliance comes equipped with our "Night Light". This appliance comes equipped with our "Night Light".
• Check for gas leaks on all gas connections up and downstream from the gas valve including the pilot tube
If in the event the lamp or lens needs to be replaced, follow these instructions.
If in the event the lamp or lens needs to be replaced, follow these instructions.
connections.
Disconnect the two wire leads at the wire nut. Remove the four screws
Disconnect the two wire leads at the wire nut. Remove the four screws
securing the accent light assembly from the relief door. Disassemble the
securing the accent light assembly from the relief door. Disassemble the
10.2 NIGHT LIGHT REPLACEMENT
light and the lamp now can be accessed
light and the lamp now can be accessed
This appliance comes equipped with our "Night Light".
Note: Do not handle the lamp (bulb) with bare fingers, protect with
note: If in the event the lamp or lens needs to be replaced, follow these instructions.
a clean dry cloth.
Disconnect the two wire leads at the wire nut. Remove the four screws
Do not handle the lamp (bulb) with bare fingers. Protect with a clean, dry
The lamp will pull straight out of the socket. Replace with Wolf Steel
securing the accent light assembly from the relief door. Disassemble the
cloth.
parts only, as lamp and lens are special "high temperature" products.
light and the lamp now can be accessed
The lamp will pull straight out of the socket. Replace with Wolf Steel
When re-installing, ensure integrity of gasket seal.
Note: Do not handle the lamp (bulb) with bare fingers, protect with
parts only, as lamp and lens are special "high temperature" products.
THE FIREBOX MUST BE SEALED.
a clean dry cloth.
When re-installing, ensure integrity of gasket seal.
When re-assembling the light assembly, care must be taken
The lamp will pull straight out of the socket. Replace with Wolf Steel
with all gaskets.
parts only, as lamp and lens are special "high temperature" products.
THE FIREBOX MUST BE SEALED.
"Light Leakage" from above the cast doors may
When re-installing, ensure integrity of gasket seal.
be noticed. The holes in the lamp housing are
THE FIREBOX MUST BE SEALED.
When re-assembling the light assembly, care must be
necessary for ventilation and must not be covered.
When re-assembling the light assembly, care must be taken
taken with all gaskets.
with all gaskets.
"Light Leakage" from above the cast doors may

10.3 PILOT INJECTOR AND ORIFICE REPLACEMENT

"Light Leakage" from above the cast doors may be noticed. The holes in the lamp housing are be noticed. The holes in the lamp housing are
necessary for ventilation and must not be covered.
necessary for ventilation and must not be covered.
9.3 pilot injector and orifice replacement
10.3 PILOT INJECTOR AND ORIFICE REPLACEMENT
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT
WARNING
!
• This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL Always light the pilot whether for the first time or if the gas supply has run out with the glass door open or
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT
LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the removed.
absence of local codes with the requirements of the provincial / state authorities having
This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL
jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code
This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL
LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the
in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.
LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the
absence of local codes with the requirements of the provincial / state authorities having
absence of local codes with the requirements of the provincial / state authorities having
jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code
A. Turn off the electrical and gas supply to the appliance.
jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code
in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.
in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.
B. Remove the cast front, glass viewing door and log set.
C. Remove the 2 securing screws. Slide the burner assembly to the right and lift
Turn off the electrical and gas supply to the appliance.
A.
A. Turn off the electrical and gas supply to the appliance.
out.
Remove the cast front, glass viewing door and log set.
B.
B.
Remove the cast front, glass viewing door and log set.
D. Using a deep socket wrench, remove the main burner orice. A back-up wrench
Remove the 2 securing screws. Slide the burner assembly to the right and lift out.
C.
C. Remove the 2 securing screws. Slide the burner assembly to the right and lift
must be used on themanifold, located below the housing to ensure that the
out.
Using a deep socket wrench, remove the main burner orifice. A back-up wrench
D.
aluminum tubing does not twist or kink. Replace the correct burner ori ce using
must be used on themanifold, located below the housing to ensure that the
pipe thread compound.
D. Using a deep socket wrench, remove the main burner orice. A back-up wrench
aluminum tubing does not twist or kink. Replace the correct burner orifice using
must be used on themanifold, located below the housing to ensure that the
E. Loosen nut and replace with appropriate injector
pipe thread compound.
aluminum tubing does not twist or kink. Replace the correct burner ori ce using
F.
Reinstall the burner ensuring that the Venturi tube ts over the orice.
pipe thread compound.
Loosen nut and replace with appropriate injector
E.
G. Turn on the gas supply and check for gas leaks by brushing on a soap and water solution.
E.
Loosen nut and replace with appropriate injector
Reinstall the burner ensuring that the Venturi tube fits over the orifice.
F.
Do not use open fl ame.
F. Reinstall the burner ensuring that the Venturi tube ts over the orice.
Turn on the gas supply and check for gas leaks by brushing on a soap and water
G.
H.
Replace the log set. Then light the pilot and main burner to ensure that the gas lines have
G. solution. Do not use open flame. Turn on the gas supply and check for gas leaks by brushing on a soap and water solution.
been purged.
Do not use open fl ame.
Replace the log set. Then light the pilot and main burner to ensure that the gas
H.
I. Replace the glass viewing door and cast front. Turn on the electrical supply to the appliance.
H.
Replace the log set. Then light the pilot and main burner to ensure that the gas lines have
lines have been purged.
been purged.
Replace the glass viewing door and cast front. Turn on the electrical supply to the
I.
I. Replace the glass viewing door and cast front. Turn on the electrical supply to the appliance.
appliance.
40
W415-2207 / C / 08.23.18
WARNING
!
WITH THE GLASS DOOR OPEN OR REMOVED.
WARNING
!
WITH THE GLASS DOOR OPEN OR REMOVED.
37.1C
37.1C
RAIL
RAIL
35
WIRE NUT
WIRE NUT
SHIELD
SHEILD
COVER PLATE
SHEILD
GASKET
GLASS LENS
COVER PLATE
GASKET
GASKET
RELIEF
DOOR
RAIL
GLASS LENS
GASKET
RELIEF
DOOR
RAIL
ORIFICE
LOCATION
ORIFICE
BURNER
LOCATION
ASSEMBLY
BURNER
ASSEMBLY
W415-1332 / A / 11.21.14
W415-1332 / A / 11.21.14
EN
EN