Night Light Replacement; Blower Placement - Napoleon GX70NTE-1 Manuel D'installation Et D'opération

Masquer les pouces Voir aussi pour GX70NTE-1:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

8.12 night light replacement

Your appliance comes equipped with our Night Light ™. The light has
been pre-wired and can be controlled from the switch on the control
panel.
It is recommended that the Night Light ™ be in the "OFF" position when
the appliance is on.
In the event the lamp or lens needs to be replaced:
Unplug the light from inside the appliance.
Remove the 4 screws that secure the lens frame. This frame retains
the glass lens.
The lamp can now be accessed. It will pull straight out of the socket.
note:
Do not handle the lamp (bulb) with bare fingers as it may be
hot. Use a clean, dry cloth for protection.
Replace the lamp with Wolf Steel parts only, as lamp and lens are
special "high temperature" products.
When re-installing, ensure integrity of gasket seal.
note:
Do not over-tighten the screws, as this could break the lens.
THE FIREBOX MUST BE SEALED.
"Light leakage" from the upper louvre area may be noticed. The holes in the lamp housing are necessary for
ventilation and must not be covered.

8.13 blower placement

WARNING
!
• Risk of fire and electrical shock!
• Turn off the gas and electrical power before servicing this appliance.
• Use only Wolf Steel approved optional accessories and replacement parts with this appliance. Using
non-listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could
result in a safety hazard and will void the warranty and certification.
• Ensure that the fan's power cord is not in contact with any surface of the appliance to prevent electrical
shock or fire damage. Do not run the power cord beneath the appliance.
• The wire harness provided in the blower kit is a universal harness. When installed, ensure that any excess
wire is contained, prevent it from making contact with moving or hot objects.
This appliance comes equipped with a blower, a heat sensor, variable on/off speed control and a power cord.
The blower is thermally activated, so when it is turned on, it
will automatically start approximately 15 minutes after lighting
the appliance and will run for approximately 30 minutes after
the appliance has been turned off. Use of the fan increases the
output of heat. Air, drawn in through the lower louvre access
door, is driven up the back of the firebox, and exhausted as hot
air between the upper louvres.
A.
Open the lower control area.
B.
Remove the control panel (3 screws).
Unplug the blower from the junction box or turn off the
C.
power to the appliance if hard wired.
D.
Undo the fastener at the left side of the blower
mounting plate. The blower should now slide to the
left, away from the mounting tab.
E.
Finally, disconnect the slip-on connectors at the motor
of the blower.
Drywall dust will penetrate into the blower bearings, causing irreparable damage. Care must be taken to prevent
drywall dust from coming into contact with the blower or its compartment. Any damage resulting from this condi-
tion is not covered by the warranty policy.
SPECIFIC BLOWER INSTALLATION
INSTRUCTIONS MUST BE ADDED HERE.
THIS TEMPLATE MUST BE USED WITH ANY
APPLIANCE THAT OFFERS THE BLOWER AS
AN OPTION OR COMES STANDARD WITH THE
APPLIANCE... AS PER THE STANDARD.
LENS ASSEMBLY
FIREBOX TOP
G
B
VARIABLE SPEED SWITCH
W
BLOWER REPLACEMENT
B
A
35.1
operation
EN
SCREWS
GASKET
LENS
FRAME
HEAT SENSOR
FAN
C
31
W415-1793 / B / 08.23.18

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Gx70pte-1Ascent x 70 serie

Table des Matières