Fireplace (Zp); Brine Earth Heat Exchanger (Zp 1, Hp Switching Contact) - Maico RLS T2 WS Notice De Montage Et Mode D'emploi

9 Unit settings menu
9.6.6 CO2 value / VOC value / Rel. humidity
control voltage 0 V/10 V
Parameters: CO value control voltage 0 V
2
Set value: 0 ... 800 ... 900 ppm
Parameters: CO value control voltage 10 V
2
Set value: 900 ... 1230 ... 3000 ppm
Parameters: VOC value Control voltage 0V
Set value: 0 ... 800 ... 900 ppm
Parameters: VOC value Control voltage 10V
Set value: 900 ... 1230 ... 3000 ppm
Parameters: Rel. humidity control voltage 0 V
Set value: 0 ... 100 % r. h.
Parameters: Rel. humidity control voltage 10 V
Set value: 0 ... 100 % r. h.
Control voltages 0 V and 10 V are used to define
the characteristic curves of the sensors. The
sensor characteristic curve must be linear.

9.7 Fireplace (ZP)

Function can be switched on with an additional
circuit board ZP.
Parameters: Fireplace safety function
Set value: No / Yes
Activates the fireplace function if the ventilation
unit is operated in conjunction with a fireplace.
After installation, the optional additional circuit
board must be switched to active with yes.
9.8 Brine earth heat exchanger (ZP 1,
HP switching contact)
Additional circuit board ZP 1 = accessories for
ventilation units:
WS 310/410, WS 320/470, WS 170, WS 160 Flat,
WS 300 Flat
Option for connecting to main circuit board with
HP switching contact on
WS 310/410, WS 320/470, WS 160 Flat, WS 300
Flat and Trio.
Parameters: Brine earth heat exchanger
Set value: no / yes
Parameters: Brine circulation pump regulation
Set value: regulated / unregulated
Parameters: T air inlet offset heating
Set value: 0 ... 2 ... 5 K
Parameters: T air inlet, hysteresis heating
Set value: 1 ... 6 K
Parameters: T air inlet, hysteresis cooling
Set value: 2 ... 6 K
46
WS 310/410, WS 320/470, WS 170, WS 160
Flat, WS 300 Flat: Pre-requirements for the ad-
ditional circuit board 1 = DIP switch of ZP 1
set to brine earth heat exchanger and activ-
ated with brine earth heat exchanger para-
meter.
Additional circuit board 1 can be used to control a
brine earth heat exchanger with a regulated or
unregulated pump. A brine earth heat ex-
changer with an unregulated pump can be con-
trolled via the switching contact.
WS 310/410, WS 320/470, WS 160 Flat, WS
300 Flat and Trio: For connection on switching
contact → Basic settings.
Pre-requirements for connection on switching
contact: Brine earth heat exchanger is selected
under `Switching contact´ parameter (→ Switch-
ing contact function [} 39]). The T air inlet offset
heating is needed so that when a brine earth heat
exchanger and PTC heat register are present in
the ventilation unit, heating is first undertaken us-
ing the heat exchanger. An electric heat register
is only activated when the temperature drops fur-
ther.
T air inlet hysteresis cooling relates to the T sup-
ply air min cooling parameter → T supply air min.
cooling [} 44].
Conditions for heating
Switch on brine CP when
• T air inlet (air temperature in outside air con-
nector) < minimum air inlet temperature (factory
setting) + T air inlet offset heating.
Switch off brine CP with unregulated pump
when
• T air inlet (air temperature in outside air con-
nector) > minimum air inlet temperature (factory
setting) + T air inlet offset heating + 1 K.
Switch off brine CP with regulated pump when
• the control voltage has fallen to 0 V.
Conditions for cooling
Switching on brine CP
The air is cooled when all 3 conditions are met:
• Summer season. Does not apply to single con-
trol unit in solo mode because the `Season´
parameter is not queried.
• T (room temperature) > set maximum room
R
temperature → Room temperature adjustment
[} 43] + 1 K