Name And List Of Components; Assembling; Ø5 L=130 Mm And L=135 Mm Chainstays; Installing The Bicycle - Elite TURNO Mode D'emploi

EN
• Turno is compatible with bikes with 130 to 135
mm hubs with 5 mm diameter quick release and
with bikes with 12 mm x 142 mm thru-axle hubs.
• Turno cannot adjust resistance like an interactive
hometrainer; simulation takes place without an
N°1 Turno body
N°2 Freehub body spacer
N°1 Chainstay adapter
N°1 Chainstay L left adapter=130-135 mm (5,1-5.3 inch)
N°1 Chainstay L right spacer=142 mm (5,6 inches)
N°1 Chainstay L left spacer=142 mm (5,6 inch)
N°2 Feets
* Quick release lever not supplied with this product.

ASSEMBLING

• Disassemble the Turno body (Rif. A)
• Place the Turno body (Rif. A) vertically as
indicated (Pic.1) and hold it in place with the
upper handle
• Rotate the foot tube 90° and place it in the pro-
per bracket welded to the leg (Pic. 1 and Pic. 2).
• Tighten the safety knob (Pic. 3).
• Spread the leg until you can hear the safety
lever click (Pic.4 and Pic. 5).
• (Pic. 6) shows the installation of feet (Rif. G) on
the Turno foot tube (Rif.A).
INSTALLING THE SPROCKET
CASSETTE ON THE Turno
FOR Ø5 L=130 mm and L=135 mm
CHAINSTAYS
• Assemble the sprocket cassette on the freehub
by aligning the groove profiles.
• In order to use a Shimano ® / SRAM ® 9/10
cassette, or others that employ the Shimano ®
standard, you need to place the spacer (Rif. B) on
the freehub before inserting the sprocket cassette
(Pic. 7).
• If you're installing a 11-speed cassette by
Shimano ® / SRAM ® or by other manufacturers
that use the Shimano ® Standard, place the
10

NAME AND LIST OF COMPONENTS

Your Turno hometrainer includes:
automatic resistance adjustment. Resistance is
obtained and varied by changes in speed and/or
gearing.
• Elite cannot be held accountable for any
malfunction due to use with third party apps.
sprocket cassette onto the freehub body without
using the spacer. (Pic. 8) (Rif. B)
• Using the torque wrench, tighten the lock ring
supplied with the cassettes onto the freehub body
(Pic. 9).
CAUTION!
Strictly follow the instructions provided by the
cassette manufacturer with regard to specific in-
stallation techniques, the need for additional spa-
cers and torque specifications.
NOTE: please contact your dealer if you have
questions or are unable to install the cassette.
The warranty does not cover any DAMAGE to the
bicycle and/or Turno in the event of incorrect in-
stallation.
• Turno includes the correct 5 mm diameter quick
release adapter for dropout spacing ranging
from 130mm (5,1 inches) to 135 mm (5,3 inches).
Therefore, on bikes with 130-135 mm (5,1 to 5,3
inches) dropout spacing, insert the left dropout
adapter (Rif. D) (Pic. 10). Please consult the para-
graph on page 11 for bikes with 12 mm diameter
(0.47 in.) and 142 mm.

INSTALLING THE BICYCLE

• Loosen the bike's rear brake and place the chain
on the smallest rear sprocket and the largest front
chainring. Remove the quick release from the rear
wheel.
(Ref. A)
(Ref. B)
(Ref. C)
(Ref. D)
(Ref. E)
(Ref. F)
(Ref. G)