Elite TURNO Mode D'emploi page 18

EN
INSTALLATION OF
CAMPAGNOLO
COMPATIBLE CASSETTE
FREEHUB BODY
• To replace the original freehub body installed on
Turno with the accessory body compatible with
Campagnolo ® 9/10/11 speed cassettes, follow
the procedure below:
1) Unscrew the adapter on the cogset shaft (Pic.
27).
2) Remove the freehub body from the Turno shaft
(Pic. 28).
3) Fully insert the Campagnolo
tible freehub body (Pic. 29-30).
4) Tighten the cog set shaft adapter using a 5 mm
hex wrench to a torque of 5 Nm (44in-lbs). Use a
medium-strength oil tolerant threadlocker to lock
the adapter on the shaft.
• You can now mount your Campagnolo ® 9/10/11
speed cassette onto the freehub body without
using the spacers (Ref. B) (Pic. 31) (only for 11
speeds).
ATTENTION!
Strictly follow the instructions provided by the
cassette manufacturer with regard to specific in-
stallation techniques, the need for additional spa-
cers and torque specifications.
NOTE: please contact your dealer if you have
questions about installation or if you cannot install
the cassette. The warranty does not cover any
DAMAGE to the bicycle and/or Turno in the event
of incorrect installation.
MAINTENANCE
Turno does not require any specific scheduled
maintenance, however the following precautions
are recommended:
• wipe the trainer clean with a cloth after each trai-
ning session to prevent the accumulation of dust
and sweat;
• do not clean or degrease the bicycle chain whi-
le the bike is mounted on Turno as solvents can
cause irreparable damage to the bearings or other
internal mechanical parts;
• check that the quick release is properly secured
and fully working before every training session;
• The tension of the internal transmission belt is
calibrated and checked on each product in the
assembly line; such tension might however di-
minish after prolonged use or a particularly stre-
nuous session, thus creating an imperfect force
12
9/10/11 SPEED
®
®
cassette compa-
transmission to the resistance system. If that's
the case, increase tension on the transmission
belt by doing as follows:
1) Unscrew the regulator screw-lock by one turn
so you can work on the regulator (Pic. 32).
2) Turn the adjusting nut half a turn to tighten the
belt correctly (Pic. 33).
3) Tighten the adjustment locking screw (under
point 1) by one full turn to set the adjustment.
4) if the belt is still uneven after performing this
operation, repeat step 2) and retest.
WARNINGS
• Turno becomes hot during use. Wait for it to cool
before touching the resistance unit covers.
• Use the Turno trainer as described in the ma-
nual.
• Turno is not equipped with an emergency brake.
• Turno has been designed and manufactured to
ensure maximum safety of the user and/or third
parties, but people, children and pets should be
kept away from the trainer during use as con-
tact with the moving parts of the trainer and the
bicycle may result in damage or injury.
• Never put your fingers or foreign objects of any
kind through the slots on Turno, as there will be
high risk of damage to the trainer and/or serious
physical injury.
• Before you start training, place the trainer in a
suitable location, away from any potentially dan-
gerous objects (furniture, tables, chairs...) so as to
avoid any risk of accidental or inadvertent con-
tact.
• The Turno is to be used by only single rider at
a time.
• Always check the safety and stability of the
bicycle on Turno before training.
• No part of the product has any use beyond its
original application. The warranty will be void if the
unit has been opened or tampered with.
• Since the feet are made of soft non-slip mate-
rial, they may leave traces of rubber on the floor
during use.
• If the trainer needs to be shipped for technical
support and/or any other reason, it must be ship-
ped in its original box. Damage due to a failure to
use the original packaging is not covered by the
warranties.
NOTE: please consult your distributor or seller be-
fore shipping the hometrainer or its components
to Elite's assistance. Unplanned shipments will
not be accepted.