Note; Name And List Of Components; Assembling The Drivo; Disclaimer - Elite DRIVO Mode D'emploi

EN

NOTE

- Elite cannot be held responsible for any malfunction in-
volving third party software / app / device.
- The two communication protocols are mutually exclu-
sive, so Drivo sends data either via ANT+™ or Bluetooth
Smart, never with both at the same time; when a protocol
connects, Drivo stops using the other one.
- ANT+™ and Bluetooth Smart protocols are mutually
exclusive and cannot be used simultaneously; when a con-
nection to a protocol is successful, Drivo stops exchanging
data with the other protocol.
- The presence of high-voltage electric lines, traffic lights,
electric railway lines, bus or tram electric lines, television
sets, automobiles, cycle computers, gym equipment and
mobile phones inside the operating range of the console,
etc., can be the cause of interference. Therefore the use
of other wireless receivers may alter or completely inhibit
operation of the Drivo due to such interference.
Do not expose the Drivo to direct sunlight for long periods
when they are not in use.

NAME AND LIST OF COMPONENTS

Your Drivo electronic trainer is made of the following components:
N°1 Drivo body
N°2 Freehub body spacer
N°1 Chainstay adapter
N°1 Power pack
N°1 Chainstay L right spacer=142 mm (5,6 inches)
N°1 Chainstay L left spacer=142 mm (5,6 inch)
N°1 Chainstay L left adapter=130-135 mm (5,1-5.3 inch)
N°2 Feets
N°1 Quick release
CD-ROM
DVD ROM

ASSEMBLING THE DRIVO

- Disassemble the Drivo body (Rif. A)
- Place the Drivo body (Rif. A) vertically as indicated (Pic.1)
and hold it in place with the upper handle
- Rotate the foot tube 90° and place it in the proper bra-
cket welded to the leg (Pic. 1 and Pic. 2).
- Tighten the safety knob (Pic. 3).
- Spread the leg until you can hear the safety lever click
(Pic.4 and Pic. 5).
- (Pic. 6) shows the installation of feet (Rif. H) on the Drivo
foot tube (Rif.A).
38

DISCLAIMER

Elite S.r.l. is not liable for any temporary or permanent da-
mage to the physical integrity of the user, whether direct or
indirect, resulting from the use of the trainer.

ATTENTION!

Drivo is equipped with a freehub body compatible with
9/10/11-speed cassettes by Shimano
other manufacturers that use the Shimano
An accessory freehub body compatible with Campagnolo
9/10/11 speed cassettes is available to replace the ori-
ginal Shimano compatible body provided on Drivo; body
replacement instructions can be found on page 40.
Drivo is compatible with 130 or 135 mm hubs and 5mm
diameter quick-release.
If you are unsure about the type of derailleur on your
bicycle, refer to the bicycle documentation or contact your
dealer to ensure compatibility with Drivo.
INSTALLING THE SPROCKET CASSETTE ON
THE DRIVO FOR M5 L=130 mm and L=135
mm CHAINSTAYS
- Assemble the sprocket cassette on the freehub by ali-
gning the groove profiles.
- In order to use a Shimano
others that employ the Shimano
place the spacer (Rif. B) on the freehub before inserting
the sprocket cassette (Pic. 7).
- If are installing a 9/10-speed cassette by Shimano
SRAM or by other manufacturers that use the Shimano
®
Standard, place the spacers (Rif. B) onto the freehub body
/ SRAM or by
® ®
Standard.
®
(Rif. A)
(Rif. B)
(Rif. C)
(Rif. D)
(Rif. E)
(Rif. F)
(Rif. G)
(Rif. H)
(Rif. I)
/ SRAM 9/10 cassette, or
® ®
standard, you need to
®
®
®
/
®