09_Power Value Accuracy; 10_Cadence Sensor; 11_Heart Rate Monitor; 12_Using The Suito-T With The Software / App / Device - Elite Suito-T Mode D'emploi

09_POWER VALUE ACCURACY

Power data sent by SUITO-T is the result of multiple
calculations. These calculations take into account pedalling
speed, hometrainer brake and other factors.
Elite calibrates every single SUITO-T in order to improve
accuracy and reduce any margin of error, though some
factors might change over time and thus decrease power
accuracy.
Spindown is a hometrainer calibration procedure that
evaluates changes arising from prolonged use and
compensates their influence on the resistance generated by
the hometrainer.
Procedure:
It's important to conduct the calibration when the hometrainer
has been working for at least 10 minutes.
To conduct the procedure, select the related command on
the app or My E-Training software and follow the instructions.
The procedure start command can be found inside the
settings page of the app.
The procedure requires to start pedalling and increase speed
up to a pre-determined value.
Stop right away once you're notified to stop pedalling.
After a few seconds the procedure will notify that the
calibration procedure has been successfully completed.
The spindown value is then memorized in the SUITO-T so the
correct power data is always sent to every connected device,
including non-Elite third parties software / apps / devices.
Note:
-The previous calibration procedure can also be conducted
with software / apps / devices other than Elite's.
- Do not lift your feet from the pedal until the procedure is
complete.
- The aforementioned notes are no longer valid if the
hometrainer connects to your bike's ergometer (if available)
as power is no longer calculated but measured by the sensor
on the bicycle. Please read the "Power Meter Link (PML)"
chapter for further info.

10_CADENCE SENSOR

The SUITO-T uses an innovative "sensorless" system and it's
obtained via sophisticated speed-based calculations.
When maintaining a high pedal cadence at low resistance
levels, there may occasionally be a slight inaccuracy in the
cadence value since it is the result of calculation and not
direct monitoring. This occurs especially with fast pedalling
and low resistance.
Should the "sensorLess" system not be accurate enough, you
can purchase a wireless sensor to attach to the bike/crank.
Most apps/software/devices give you the ability to select a
sensor as source for the cadence value.

11_HEART RATE MONITOR

- SUITO-T hometrainer does not read heart rate monitor data.
Heart rate monitor data can be read directly from a device
that includes a heart rate function.
- Compatibility with various types of heart rate monitors
depends on the device / software / app being used only
ANT+ and is also compatible with Bluetooth Smart monitors
allowing connection with monitors by both protocols.
12_USING THE SUITO-T WITH THE SOFTWARE
/ APP / DEVICE
We suggest using the My E-Training software/app, available
on iOS, Android, Windows and Mac OS.
My E-Training is a complete system with several training
modes, including videos, configurable software, Google Maps
races, Internet competitions and much more.
It's possible to use third-party software that is compatible
with the hometrainer communications protocol/standards.
There are several software/apps/devices currently on the
market that can connect to the SUITO-T.
Please refer to the instructions for the specific software/app/
device for a proper connection to the hometrainer.
Before beginning the connection procedure with any app,
make sure that the hometrainer is powered up and is not on
the energy saver mode. The supplied hometrainer charger
must be connected to a power source.
The hometrainer motherboard features LED lights indicating
the current hometrainer status. Please check the "Status LED
lights" paragraph for an in-depth description.

13_NAME AND LIST OF COMPONENTS

Your SUITO-T includes:
N.1 SUITO-T body
N.2 Freehub body spacer
N.1 Chainstay adapter
N.1 Right rotating chainstay adapter L=130-135mm (D)
N.1 Left rotating chainstay adapter L=130-135mm
N.1 Right rotating chainstay adapter L=142mm
N.1 Left rotating chainstay adapter L=142mm
N.1 Quick Release
N.1 Riser block
N.1 Power supply
WARNING: adapters ref. C, D, E, F, G are small sized
components and might easily be misplaced or lost. If
you move the hometrainer it's advisable to remove the
adapters and store them in their bag as they might easily
slip out during transport.
Any spare parts are available in our online store or by
directly contacting Elite and/or your country's distributor.
EN
(A)
(B)
(C)
(E)
(F)
(G)
(H)
(I)
(L)
43