Moser ChromStyle 1871 Mode D'emploi page 6

ENGLISH
· When the speed of the battery audibly begins to slow down, the battery has a remaining capac-
de
ity of approx. 2 - 3 minutes. Charging the battery.
· When the battery has fully run down, the machine will switch itself off automatically.
en
· Note: In case of insufficient maintenance of the blade set, the operating time can be reduced
considerably.
fr
Cutting-length adjustment
The cutting length can be adjusted to between 0.7 mm and 3 mm (5 possible positions) using the
it
cutting-length adjustment integrated into the blade set (Fig. 4). To do this, set the adjustment lever
to the desired position and let it snap into place.
es
Cutting with attachment combs
pt
The appliance can also be operated with attachment combs. In order to achieve the indicated
cutting length, the cutting length adjustment lever should be set to position 1 (Fig. 4). The follow-
ing attachment combs are included as standard: 3 mm, 6 mm, 9 mm and 12 mm cutting lengths.
nl
Attachment combs with 18 mm and 25 mm cutting length are available as optional accessories.
sv
Attaching/removing the attachment comb
· Slide the attachment comb on to the blade set in the direction of the arrow until it reaches the
no
limit stop (Fig. 5a).
· The attachment comb can be removed by pushing it in the direction of the arrow (Fig. 5b).
fi
Cleaning and Care
· Do not immerse the appliance in water!
tr
· After each use, remove the attachment comb and use the cleaning brush to remove cut hairs
from the housing opening and from the blade set. To do this, remove the blade set (Fig. 6a)
pl
and press the cleaning lever (Fig. 7). This allows the cut hairs that accumulate between the bot-
tom blade and the top blade to be easily removed using the cleaning brush (EASY CLEANING).
cs
· The charging contacts on the appliance and charging stand should always be kept clean.
· Only wipe the appliance with a soft cloth, which may be dampened slightly. Do not use solvents
sk
or abrasives!
· The blade set can be cleaned with hygienic spray, order no. 4005-7051. Do not use any other
cleaning agents.
hu
· For a long-lasting, good cutting performance, it is important to oil the blade set frequently
(Fig. 8). Use only blade set oil for this purpose, order no. 1854-7935 (200 ml).
sl
· Blade set oil and hygienic spray is available from your dealer or our Service Centre.
· If the cutting performance deteriorates after long use despite regular cleaning and oiling, the
ro
blade set should be replaced.
bg Automatic Sensor System
To ensure that your new hair cutting appliance enjoys a long service life, the appliance needs to be
cleaned and oiled on a regular basis (see section Cleaning and Care in the user instructions). To
ru
give you advance notice of an urgent need for maintenance care, your hair cutting appliance has
been equipped with an automatic sensor system. This system automatically recognises when the
uk
blade set needs oiling or cleaning. Consistent heavy soiling or lack of oil can lead to early wear
and tear of the appliance.
el
ar
12
Should the sensor system recognise such a situation, an acoustic signal will sound and the LED
display will blink for 2 minutes after the appliance has been switched off. The acoustic signal and
the blinking of the LED display can be cancelled by briefly switching the appliance on and off.
Before using the appliance again, it is urgently recommended to clean the appliance and oil the
blade set. For this purpose, please proceed as follows (failure to observe these instructions may
result in damage to and early failure of the appliance and will void all guarantee claims):
· Switch off the appliance using the on/off switch (Fig. 2b).
· Remove the attachment comb and the blade set and use the cleaning brush to clean the open-
ing of the housing and the blade set. (Fig. 7).
· Oil the blade set (Fig. 8).
Changing the blade set
· Switch off the appliance using the on/off switch (Fig. 2b).
· The blade set can be removed by sliding it away from the housing in the direction of the arrow
(Fig. 6a).
· Replace the blade set by hooking it into the housing and pressing it down until it clicks into posi-
tion in the housing (Fig. 6b).
Disposal in EU countries
D o not dispose of the appliance with domestic refuse. As part of the EU Directive govern-
ing the disposal of electrical and electronic equipment, the appliance is accepted free of
charge by local waste collection points or recycling centres. Correct disposal will ensure
environmental protection and prevent any potentially harmful impacts on people and the
environment.
Disposal in non-EU countries
· Please dispose of the appliance at the end of its service life in an environmentally friendly
manner.
· Disconnect the plug-in transformer from the mains power supply and switch on the appliance to
discharge the battery completely.
· Remove the blade set (Fig. 6a) and use a screwdriver to remove the screws in the opening of
the housing (Fig. 9). Pull the housing parts apart and remove the entire drive with the PCB
(Fig. 10).
· Pull battery off circuit board. If necessary, use a screwdriver to pry them off (Fig. 11).
· Take the batteries to an appropriate collection point.
· Once the batteries have been removed, the appliance may no longer be connected to the
mains!
ENGLISH
de
en
fr
it
es
pt
nl
sv
no
fi
tr
pl
cs
sk
hu
sl
ro
bg
ru
uk
el
ar
13