Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Although there are typically no video connections for a CD Player, the RSP-
1582 can assign another video input to the CD or XLR input. The Video
choices are HDMI 1-8 (Front), Last Video Source, or off. HDMI 1 video input
is assigned to CD and XLR as the default setting.
Connecting a Tuner
See Figure 9
Digital audio connection: If using an HD Radio or other digital tuner, connect
the digital output of the tuner to any one of the DIGITAL IN OPTICAL 1–3
or DIGITAL IN COAXIAL 1–3 inputs on the RSP-1582.
NOTE: The Tuner source by default does not allow the selection of
a digital input. Please use VIDEO 1 - 8, if connecting a Tuner with a
digital input.
Analog audio connection: If using an analog tuner, connect the left and
right analog outputs from the tuner to the pair of audio input jacks labeled
TUNER on the RSP-1582. Make sure that you connect the right channel to
the R input jack and the left channel to the L input jack.
Although there are typically no video connections for a Tuner the RSP-1582
can assign another video input to the Tuner input. The Video choices are
HDMI 1 - 8 (Front), Last Video Source, or off. HDMI 1 video input is assigned
to the Tuner input, as a default setting.
Connecting an iPod/iPhone
See Figure 11
Connect the iPod/iPhone to the front USB socket.
NOTE: The audio inputs CD, PHONO, XLR, MULTI, USB, PC-USB,
BLUETOOTH, and TUNER are set to HDMI 1 video input as the factory
default. This can be changed to HDMI 1-8, Last Video Source, or off.
Operating the RSP-1582
Considering its large number of features, settings and options, this Rotel
RSP-1582 is remarkably easy to operate. The key to operating the unit is its
system of On-Screen Displays (OSD) which guide you through various choices.
To guide you through the operation of the unit, this section of the manual
starts with explaining the basic layout and functions of the front panel and
the remote control. This is followed by explanation of basic operations
such as turning the unit on and off, adjusting volume, selecting a source for
listening, etc. Following that is a detailed explanation of surround sound
modes and how to configure the unit for various types of recordings. All of
these are features that may be used in normal operation. The last section
of the manual (Configuration) details options that may be selected during
initial setup and configuration of the unit, many of which will be set once
and then left untouched.
Throughout this manual, numbers in square boxes refer to the main unit
illustration at the front of this manual. Letters in circles refer to the remote
handset illustration. When both appear, the function is found on both the
unit's front panel and on the remote. When only one appears, that function
is found either only on the main unit or only on the remote.
Front Panel Overview
The following is a brief overview of the controls and features on the front
panel of the unit. Details concerning the use of these controls are provided
in subsequent sections of this manual describing various tasks.
Front Panel Display
3
The Display on the front panel shows the complete OSD menu of the unit.
When the OSD is not in use, the display shows source selected and type
of audio mode the unit is in receiving or processing.
IR Remote Sensor
2
This sensor receives IR signals from the remote control. Do not block this sensor.
NOTE: The remainder of the buttons and controls on the front panel
are described in the Overview of Buttons and Controls section.
Remote Control Overview
The RSP-1582 is supplied with an easy to use remote control RR-CX100.
The RR-CX100 can be configured to use IR codeset 1 or IR codeset 2 in
case the unit is conflicting with other Rotel models. Push and hold the TUN
button and 1 (or TUN and 2 for codeset 2) at the same time and hold for
approximately 5 seconds until the backlights on the remote control blink
on then off then release both buttons. This sets the remote control to use
codeset 1 (or codeset 2 if TUN and 2 are held). The System menu in the
OSD includes a configuration option to set the processor to either codeset 1
or codeset 2. The factory default for the remote and processor is codeset 1.
The RR-CX100 can also control an attached Rotel CD player. The CD player
functions include Play, Stop, Pause, Track Forward, Track Back, Fast Forward,
Fast Reverse. To activate these functions press the CD button on the remote.
If the CD is attached to the XLR source input these functions can be activated
by pressing the XLR button. To change the CD player functions to operate
after pressing the XLR button press and hold the XLR and 1 button for 5
seconds until the backlight LEDs blink twice times then release. To disable
XLR sending the CD control functions press and hold the XLR and 0 button
for 5 seconds until the backlight blinks.
The transport buttons will only operate for CD control after the CD or XLR
button is pressed on the remote. If a different input is selected from the
remote these buttons will no longer send the CD transport IR commands.
Overview of Buttons and Controls
This section provides a basic overview of the buttons and controls on the
front panel and the remote control. Detailed instructions on the use of these
buttons are provided in the more complete operating instructions in the
following sections.
19
Publicité
Chapitres
Table des Matières
