Connecting The Speakers; Troubleshooting; Front Panel Power Indicator Is Not Lit; No Sound - Rotel RMB-1095 Manuel D'utilisation

Connecting the Speakers

See Figure 2
The RMB-1095 has five sets of color coded
binding posts. These
SPEAKER CONNECTORS
cept bare wire, connector lugs, or dual ba-
nana type connectors (except in the European
Community countries where their use is not
permitted).
Route the wire from the RMB-1095 to the
speakers. Give yourself enough slack so you
can move the components enough to allow
access to the
SPEAKER CONNECTORS
If you are using dual banana plugs, connect
them to the wires and then plug into the backs
of the . The collars of the
SPEAKER CONNECTORS
should be screwed in all
SPEAKER CONNECTORS
the way (clockwise).
If you are using terminal lugs, connect them
to the wires. If you are attaching bare wires
directly to the
SPEAKER CONNECTORS
the wire conductors and strip back the insu-
lation from the end of each conductor. Be care-
ful not to cut into the wire strands. Unscrew
(turn counterclockwise) the
SPEAKER CONNEC
collars. Place the connector lug around
TORS
the shaft, or insert the bundled wire into the
hole in the shaft. Turn the collars clockwise
to clamp the connector lug or wire firmly in
place.
NOTE: Be sure there are no loose wire
strands that could touch adjacent wires or
connectors.
9

Troubleshooting

Most difficulties in audio systems are the re-
sult of poor or wrong connections, or improper
ac-
control settings. If you encounter problems,
isolate the area of the difficulty, check the con-
trol settings, determine the cause of the fault
and make the necessary changes. If you are
unable to get sound from the RMB-1095, re-
fer to the suggestions for the following con-
ditions:
Front Panel Power Indicator
.
Is Not Lit
No main power to the RMB-1095. Check the
front panel
POWER SWITCH
is set to the position. Check AC power con-
ON
nections at the amplifier and the AC outlet.
, separate
-

Specifications

Continuous Power Output (20-20 kHz, < 0.03%)
DIN Power Output (1kHz, 1%)
Total Harmonic Distortion (20Hz-20kHz, 8 ohms)
Intermodulation Distortion (60 Hz : 7 kHz, 4:1)
Frequency Response (+0.5 dB, -3 dB)
Damping Factor (20-20,000 Hz, 8 ohms)
Speaker Impedance
Signal to Noise Ratio (IHF A network)
Input Impedance/Sensitivity
Power Requirements
Power Consumption
Dimensions (W x H x D)
Weight (net)
All specifications are accurate at the time of printing.
Rotel reser ves the right to make improvements without notice.
THX and the THX logo are trademarks of Lucasfilm Ltd. All rights reserved.

No Sound

If the amp is getting AC power, but is pro-
ducing no sound, check the
DICATORS
If not, check all of your connections and control
settings on associated components. Check the
INPUT SELECTOR SWITCH
panel to be sure that its setting matches the
type of input you are using.

Protection Indicator Is Lit

The front panel
when the RMB-1095 protection circuits have
shut off the amplifier. Typically, this occurs only
when the ventilation openings are blocked,
. Make sure that it when there is faulty speaker wiring, or after
a period of extreme use. Turn off the system
and wait for the amp to cool. Then push the
front panel
the protection devices. If the problem is not
corrected or reoccurs, there is a problem with
the system or the amplifier itself.
English
PROTECTION IN
on the front panel. If lit, see below.
on the RMB-1095 back
PROTECTION INDICATORS
in and out to reset
POWER SWITCH
200 watts/ch into 8 ohms
330 watts/ch into 4 ohms
< 0.03%
< 0.03%
15Hz-100kHz
400
4 ohms minimum
116 dB
33 k Ohms/1.5 volt (unbalanced)
33 k Ohms/±1.5 volt (balanced)
115 Volts, 60 Hz (U.S. version)
230 Volts, 50 Hz (European version)
800 Watts
440 x 240 x 398 mm
17 x 9 x 15 in
3/8 1/2 3/4
34 kg, 75 lb.
-
light