Ryobi EWS-1266 Manuel D'utilisation page 8

GB
FR DE ES IT
P ARTICULAR REQUIREMENTS FOR
CIRCULAR SAWS
Use extra caution when making a "plunge cut"
■
into existing walls or other blind areas. The
protruding blade may cut objects that can cause
kickback.
Safety instructions for saws with lower guard
Check lower guard for proper closing before each
■
use. Do not operate the saw if lower guard does
not move freely and close instantly. Never clamp
or tie the lower guard into the open position. If
saw is accidentally dropped, lower guard may be
bent. Raise the lower guard with the retracting handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of
cut.
NOTE: Alternate wording may be substituted for
"retracting handle".
Check the operation of the lower guard spring.
■
If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up debris.
Lower guard should be retracted manually only
■
for special cuts such as "plunge cuts" and
"compound cuts." Raise lower guard by retracting
handle and as soon as blade enters the material,
the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
NOTE: Alternate wording may be substituted for
"retracting handle".
Always observe that the lower guard is covering
■
the blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to
stop after switch is released.
Additional safety instructions for all saws with riving
knife
Use the appropriate riving knife for the blade
■
being used. For the riving knife to work, it must be
thicker than the body of the blade but thinner than the
tooth set of the blade.
Adjust the riving knife as described in this
■
instruction manual . Incorrect spacing, positioning
and alignment can make the riving knife ineffective in
preventing kickback.
Always use the riving knife except when plunge
■
cutting. Riving knife must be replaced after plunge
cutting. Riving knife causes interference during
EWS-1266&EWS-1366_24lgs manual_03_2009.12.04.indd Sec1:2 EWS-1266&EWS-1366_24lgs manual_03_2009.12.04.indd Sec1:2
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
plunge cutting and can create kickback.
For the riving knife to work, it must be engaged
■
in the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
Do not operate the saw if riving knife is bent. Even
■
a light interference can slow the closing rate of a
guard.
DESCRIPTION
1. Spindle lock button
2. Hex-head bolt
3. Spanner
4. Outer blade washer
5. Lower guard
6. Lower guard lever
7. Upper guard
8. Blade
9. Inner blade washer
10. Dust nozzle
11. Riving knife
12. Depth lock knob
13. Base plate
14. Depth of cut
15. Depth scale
16. Bevel adjustment knob
17. Bevel scale
18. Trigger switch
19. Safety button
20. Line guide
21. Depth adjustment lug
22. Live Tool indicator
23. Laser guide button
24. Laser guide
25. LED button
26. LED light
SPECIFICATIONS
Voltage
Input
No load speed
Bore size
Blade size
Cutting capacity
at 0°
at 45°
Bevel scale
2
LT EE HR SI SK GR
EWS-1266 EWS-1366
230V 110V/230V
1,250 W 1,250 W/1,350 W
4,500 min -1 4,500 min -1
16 mm 16 mm
190mm 190 mm
66 mm 66 mm
38 mm 38 mm
0 – 45° 0 – 45°
12/4/09 1:57:51 PM 12/4/09 1:57:51 PM
TR