Publicité
Les langues disponibles
Les langues disponibles
Damaged safeguards and parts must be either repaired or
replaced by an authorized workshop, unless specified
otherwise in this operation manual.
Replace damaged switches in a service workshop. Do not
use the devices with malfunctioning ON/OFF switch.
WARNING!
Use of non-compliant accessories may result in an injury.
Have your device repaired by an electrician only!
This device complies to applicable safety provisions.
Repairs may be performed by an electrician with the use of
genuine spare parts, otherwise the user may be exposed
to injury hazard.
Safety instructions specific for this device
•
This device may be used outside only,
however, it must be protected against
moisture or rain.
Gas cylinder must be always protected against
•
freeze and minus temperature at any times.
The device may be used for heating only.
•
•
Attention! Open flame tightness test is
strictly prohibited.
Do not operate under ground level.
•
Do not move and lift the device if in use.
•
Radiation area must be at least 2 metres
•
from persons and all flammable substances.
Keep 50 cm distance between walls and rear or
•
sides of the device.
If gas leaks (smell), close the gas cylinder valve
•
immediately and keep the device out of reach of
all flammable sources.
Check tightness of all connections.
•
•
If gas leakage remains, call an expert before re-
commissioning.
Assembly and maintenance of the device must
•
comply with laws and directives of a country
where the device is used.
Do never turn the gas cylinder upside down
•
even though you think it is empty! This
procedure may jam the hose with residues from
the gas cylinder and cause fire hazard and
immediate damage of the device.
•
Do not disassemble the protective grid and/or
other parts of the heater.
Keep children out of reach of the burner.
•
•
Do not operate the device without supervision!
•
Do not cover the device!
Do not use for drying of clothes etc.!
•
•
Do not touch the protective grid and thermal
shield, otherwise burning injury may occur!
Assembly and commissioning instructions (Fig.
A/B/C)
Do not use the device close to flames, sparks or
flammable substances (except for substances required
for operation - here propane/butane).
Operate the device on a flat and stable surface.
Step 1 (C/1)
Plug the device to a socket (230V~50Hz).
Step 2 (C/2)
Connect the reduction valve (B/7) with the gas
•
hose connection (B/8).
Connect the reduction valve (B/7) with the fitted
•
gas hose to the gas cylinder valve (B/12).
•
Connect the gas hose connection (B/9) with the
heater.
Step 3 (C/3)
Screw out the gas cylinder valve (B/12).
Check the screw closures by tightness test
spray or use a soap liquor. Retighten, if necessary.
Step 4 (Fig. C/4)
Press ON/OFF switch (A/6).
Step 5 (Fig. C/5)
From suction side check whether the fan (A/1) revolves.
Step 6 (Fig. C/6)
If the fan (A/1) revolves, keep the gas valve
•
button (A/11) pressed and at the same time,
press repeatedly the ignition button (A/5) until
the burner ignites.
Hold the gas valve button (A/11) pressed for 10
•
to 20 more seconds.
•
Check whether the gas heater works
uninterruptedly.
Turning off (Fig. D)
Step 1 (Fig. D/1)
To turn the heater off, first screw in the gas cylinder valve
(B/12).
Step 2 (Fig. D/2)
Turn off the device with the use of ON/OFF switch (A6).
Step 3
Unplug the device from the socket to disconnect power
supply.
Replacement of gas cylinder
•
Always replace the gas cylinder outside and out
of reach of flames or flammable sources without
presence of other persons!
Close the gas cylinder valve. (B/12)
•
Screw out the reduction valve (7).
•
•
Ensure you have the reduction valve seal
available.
Connect the device to a new gas cylinder and
•
proceed according to instructions in "Assembly
and commissioning instructions".
Identification
Product safety:
The product complies with
relevant EU standards
Prohibitions:
No flame!
No smoking!
Warning:
No operation in closed
spaces!
No pulling the plug!
Publicité
