Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
V12H949001 / AN3WA100
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM:
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY:
AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT:
A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING:
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION:
A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer's responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING:
Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer's responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system. The wall to which the
mounting system is being attached may have a minimum
drywall thickness of 1/2" (12.7mm) for wood and steel stud
walls, and NO drywall on concrete walls.
2
A MOUNTING SYSTEM is the
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer's responsibility to make sure the combined weight of
all components attached to the AN3WA100 does not exceed:
•
Installed in steel stud: 35 lbs (15.9 kg)
•
Installed in 2" x 4" wood stud: 35 lbs (15.9 kg)
•
Installed in bare 8" concrete wall or 8" x 8" x 16"
bare concrete block wall: 35 lbs (15.9 kg)
WARNING:
Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING:
Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING:
Do not use this mounting system outdoors.
IMPORTANT ! :
The AN3WA100 mounting system is
designed to be used ONLY with the following Epson projector
models:
Lamp-Style
•
BrightLink Pro 1450Ui
•
BrightLink Pro 1460Ui
•
BrightLink 696Ui
•
BrightLink 697Ui
Laser-Style
•
BrightLink Pro 1470Ui
•
BrightLink 710Ui
IMPORTANT ! :
The AN3WA100 mounting system is
designed to be mounted to :
•
a bare 8" concrete or 8"x8"x16" concrete block wall; or
•
a 2" x 4" wood studs (16" on center minimum) wall with
a minimum drywall thickness of 1/2" (12.7mm); or
•
a 2" x 4"-25ga minimum steel studs (16" on center
minimum to 24" on center maximum) wall with a
minimum drywall thickness of 1/2" (12.7mm).
--SAVE THESE INSTRUCTIONS--
Installation Instructions
Publicité
Table des Matières
