Sygonix SY-MV3215 SY-3561086 Notice D'emploi page 59

Quick guide
4-channel AHD digital recorder
Item no. 1629427
Intended Use
The digital recorder is intended for recording and monitoring the images of up to four connected
cameras (not included, can be ordered separately). The device is operated via USB mouse and
with an intuitive OSD menu.
The digital recorder is particularly suitable for AHD, CVI, TVI, IP cameras. The images are
recorded onto a SATA hard drive (not included in the delivery, to be ordered separately).
For safety and approval reasons, you may not convert and/or alter the product. If you use the
product for purposes other than those described above, the product may be damaged. Moreo-
ver, the improper use involves risks such as short-circuits, fire, electric shocks, etc. Please read
the operating instructions carefully and do not discard them. If you pass the product on to a third
party, please hand over these operating instructions as well.
This product complies with the applicable national and European regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Package contents
• Digital recorder
• 4x fixing screw for hard drive
• USB mouse
• Power adapter
• Software CD (with software and manufacturer's English and German instruction manual
• Quick guide
Up-to-date operating instructions
Download the latest operating instructions via the link
www.conrad.com/downloads or scan the QR code.
Follow the instructions on the websit
Explanation of Symbols
The lightning symbol inside a triangle is intended to alert you of health hazards, e. g.,
risk of electrical shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual which must be adhered to.
The arrow symbol is used when specific tips and information on the operation are
provided.
Observe the operating instructions!
Safety Instructions
Please read the operating instructions carefully and pay particular attention to
the safety instructions. We do not assume liability for injuries/material damag-
es resulting from failure to observe the safety instructions and the information
in these operating instructions regarding the proper handling of the product.
Furthermore, in such cases, the warranty/guarantee will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons.
• If the digital recorder is used with other devices (e.g. a monitor and surveillance
cameras), the operating instructions and safety notices for these devices must
be followed.
• Any maintenance or repair work may be performed only by an expert.
• Do not leave the packaging material unattended, since it could become a dange-
rous plaything for children.
• On industrial sites, the accident prevention regulations of the association of the
industrial workers' society for electrical equipment and utilities must be followed.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
b) Power adapter/mains voltage
• The design of the plug-in power adapter complies with IEC Protection Class II
(double insulated electrical appliances). Use only a standard mains socket as the
power source for the power adapter.
• The power socket into which the power adapter is inserted must be easily ac-
cessible.
• Use only the power adapter supplied to power the digital recorder.
• Do not pull the AC adapter from the mains socket by pulling on the cable.
• Never touch a power adapter that shows signs of damage, as this could cause a
fatal electric shock!
First, switch off the mains voltage to the socket to which the wall plug transformer
is connected (switch off at the corresponding circuit breaker or, for example, re-
move the safety fuse or switch off at the corresponding RCD protective switch, so
that the socket is fully disconnected).
You can then unplug the power adapter from the mains socket. Dispose of the
faulty power adapter in an environmentally friendly way, do not use it any more.
Replace it with a power adapter of the same design.
c) Operation
• The product is not a toy. Devices operated on mains voltage should not be used by
children. Therefore, be especially careful when children are around.
Use the product where it is out of the reach of children.
• The product is intended for use in dry indoor rooms only; it must not get damp or
wet; never touch it with damp wet hands! Power adapters pose the potential risk
of a fatal electric shock!
• The product should not be exposed to extreme temperatures, direct sunlight, in-
tense vibrations or heavy mechanical stress. Protect it against dust and dirt.
• Never use the product immediately after moving it from a cold room into a warm
one. The condensation that forms might destroy the product. A power adapter also
carries the risk of a potentially fatal electric shock!
• Allow the product to reach room temperature before connecting it to the power
supply and putting it into use. In some cases, this may take several hours.
• Avoid the following adverse conditions at the location of installation and during
transport:
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows
- Strong magnetic fields such as those found close to machinery or loudspeakers
• Safe operation can no longer be assumed if:
- the product exhibits visible damage,
- the device no longer works
- the device was stored for a long period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• When setting up and operating the product, ensure that the cables are neither
bent nor squeezed.
• Handle the product with care; it can be damaged by impacts, blows or falls even
from a low height.
• Disconnect the power supply from the power socket if the product will not be used
for a while (e.g. storage).
Installation of a SATA Hard Drive
Before you open the digital recorder and install a hard disk, disconnect the digital
recorder from the power supply; Unplug the power supply from the wall outlet..
• First remove the casing lid of the digital recorder by unscrewing its retaining screws (one
screw each on the left and right and 2 screws on the rear side).
• A 8.89 cm / 3.5" SATA hard drive is suitable for installation (not included). For use as surveil-
lance device, you have to install a hard drive that can be used in continuous operation. These
are usually more expensive than „normal" hard drives.
Some manufacturers of hard drives offer hard drives that are specially designed for surveil-
lance systems.
Do not install a conventional desktop hard drive into the digital recorder as it will age
faster or read/write errors may occur when the hard drives is used in continuous
operation.
Ensure also that the hard disk used will not generate heat as the digital recorder has
no integrated fan.
• Attach the hard drive to the digital recorder by the recorder's mounting holes intended for this
purpose and 4 screws.
• Connect the power cord and the SATA cable between the hard drive and the digital recorder's
control board.
• Replace the casing lid of the digital recorder and fasten it with the screws removed earlier
in this step.