Repeat Mode; Recording Function - SOUNDMASTER PL905 Mode D'emploi

 Skip mode (skip up
1. During play or pause mode, if " Skip up
and then remain the play or pause mode.
2. During play or pause mode, if " Skip down
the track.
Remark:-
Before pressing the " CD tray open " button for changing disc
ensure the LCD resume to the original information.
- The reaction time of the CD burner is longer than normal CD player due to the complicacy system.
- Keep pressing with all difference function within a short time may cause mal-function of the system. Please re-start the
unit if this is happen.
- The reading and playback time of CD-R(W) disc is various from brand to brand. It depends on the compatibility of the
used disc.
- This device only design for normal compact disc format. Is not support any MP3/WMA format.
 Repeat mode
Press the Repeat button (48) before or during playback, a single track or all the tracks can be played in difference mode as
follow:-
(1) repeat all track
Indicator
Play mode on LCD display
Repeat all
Repeat 1 1
Off mode --------------
CD disc programming (by remote control)
Up to 32 tacks can be programmed for CD playing. Before use, be sure the system is at stop mode before
programming:-
1. Set in CD mode & stop the disc playback.
2. Press the "Program" button (46) at remote handset, " Prog " indicator will appear on LCD display. Moreover, it will indicate
program no. (P-xx) and digits for track no. to be programmed.
3. Select a desired track by pressing CD skip up
4. Press the " Program " button (46) to store the trace into memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
6. When all the desired tracks have been programmed, press CD " Play/Pause
assigned order.
7. To cancel the programmed file, press "Stop" button (11/38) until " Prog " indicator is disappear on LCD display (3).
Remark:-
- After program play and you can delete the programmed track in the order from the last one to the 1
programmed track start to played. Press stop button to set the unit in stop mode first, press " Clear " button at remote
control once, then press stop button to enter clear mode, press the Clear button again once by once. The programmed
track will delete one by one from the memory.

Recording function

Apart from the CD playback function, it can perform the CD recording function either from Phono / Tape / Aux and USB mode
respectively. All the recording track will be stored at " audio-CD " format:-
Before start, place a CD-R or CD-RW disc in the CD tray (7). The disc is able to record only if the LD display show "NO TOC ".
Remark : CD-R disc can be recorded once only and not support erase or re-record function. The playback quality of either
CD-R(W) disc is various from differences kind of audio CD player device.
Important notices:-
- The revolving speed of CD burner is higher than normal CD mechanism.
Thus, some mechanical noise and vibration of unit cabinet may occur during
operation. This is not the malfunction of the system.
- Due to the variety on the quality and the compatibility of CD-R(W) disc from
the market. Please change other brand if you found the used one is not able
to record or the performance is not so stable.
- Since the CD burner was complicate equipment, in case the power was
interrupt or wrong operation during the CD burner is running, it may cause the
system will locked and cannot eject the CD tray, switch off the power and use
a stick to stab the hole which near by the CD tray, then the CD tray will eject
portion mechanically, pull out the CD tray completely by manual and remove
the disc, then re start the system again.
/ skip down
" button (15/37) is pressed. It will go to next track and display the track no.
(2) repeat 1 (3) off mode
)
" button (15/37) is pressed. It will go back to the previous track and play
Press the " CD stop " button (11/38) first and
.
or down buttons (15/37).
19
" button (13/36) to play the disc in
st
one after the