Intended Use; Basic Safety Instructions - Burkert 6014 Manuel D'utilisation

1. OPERATING INSTRUCTIONS
The operating instructions contain important information.
▶ Read the operating instructions carefully and follow the safety instruc-
tions in particular, and also observe the operating conditions.
▶ Operating instructions must be available to each user.
▶ The liability and warranty for the product / device are void if the oper-
ating instructions are not followed.
1.1. Symbols
▶ Designates an instruction to prevent risks.
→
designates a procedure which you must carry out.
Warning of injuries:
DANGER!
Imminent danger! Serious or fatal injuries.
WARNING!
Potential danger! Serious or fatal injuries.
CAUTION!
Danger! Minor or moderately severe injuries.
Warns of damage to property:
NOTE!
2
2.2. Definition of term
In these operating instructions, the term "device" or "product" always
refers to the solenoid valve Type 6014.
2.3. Approvals
The approval mark indicated on the Bürkert type labels refers to the
Bürkert products.
e
1
03 5791
Devices which must bear the type approval mark were approved at the
Kraftfahrtbundesamt under the type approval number
e1*72/245*2006/96*5791*00
and are put into circulation with the indicated type approval mark. You
can obtain an extract of the type approval from the address below.
Bürkert Werke GmbH
Zulassungsbeauftragter,
Christian-Bürkert-Str. 13-17,
D-74653 Ingelfingen
3. BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any contingencies
and events which may arise during installation, operation and maintenance.
Risk of injury from high pressure in the equipment/device.
▶ Before working on equipment or device, switch off the pressure and
deaerate/drain lines.
Risk of electric shock.
▶ Before working on equipment or device, switch off the power supply
and secure to prevent reactivation.
▶ Observe applicable accident prevention and safety regulations for
electrical equipment!
Risk of burns/Risk of fire if used continuously through hot
device surface.
▶ Keep the device away from highly flammable substances and media
and do not touch with bare hands.
General hazardous situations.
To prevent injury, ensure that:
▶ The system cannot be activated unintentionally.
▶ Installation and repair work may be carried out by authorized techni-
cians only.
4
2. INTENDED USE
Incorrect use of the solenoid valve Type 6014 can be dangerous
to people, nearby equipment and the environment.
• The device is designed for blocking, dosing, filling and venting neutral
gaseous and liquid media.
• Do not use the device outdoors.
• Use according to the permitted data, operating conditions and
conditions of use specified in the contract documents and operat-
ing instructions. These are described in the chapter entitled "5.
Technical data".
• The device may be used only in conjunction with third-party devices
and components recommended and authorised by Bürkert.
• Correct transportation, correct storage and installation and careful
use and maintenance are essential for reliable and problem-free
operation.
• Use the device only as intended.
2.1. Restrictions
If exporting the product / device, observe any existing restrictions.
2.4. Ex approval
The Ex approval is only valid if you use the modules and components
authorized by Bürkert as described in these operating instructions.
You may use the electronic modules only in combination with the pneu-
matic valve types released by Bürkert, otherwise the Ex approval will be
void!
If you make unauthorized changes to the system, the modules or com-
ponents, the Ex approval will also be void.
▶ After an interruption in the power supply or pneumatic supply, ensure
that the process is restarted in a defined or controlled manner.
▶ The device may be operated only when in perfect condition and in
consideration of the operating instructions.
▶ The general rules of technology apply to application planning and
operation of the device.
To prevent damage to property of the device, ensure:
▶ Supply the media connections only with those media which are speci-
fied as flow media in the chapter entitled "5. Technical data" .
▶ Do not put any loads on the device (e.g. by placing objects on it or
standing on it).
▶ Do not make any modifications to the device. Do not paint the body
parts or screws.
3.1. Versions with explosion protection
DANGER!
Danger of explosion.
Improper use in the potentially explosive area may result in an explosion.
▶ Also follow the specifications in the certificate of conformity.
▶ If versions have ATEX approval, also follow the specifications in the
ATEX instructions.
Type 6014
3